HP Dl180 ProLiant DL180 Generation 5 Server Maintenance and Service Guide - Page 32

Removing power supply cables from the system board connectors J13, J23, J26, and J38 follow

Get HP Dl180 - G6 E5504 2X2gb 4Lff Svr PDF manuals and user guides
UPC - 883585990917
View all HP Dl180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

• Keep cables away from major heat sources like the heat sink. • Do not jam cables on top of expansion cards or memory modules. Printed circuit cards are not designed to withstand excessive pressure. • Keep cables clear of sliding or moveable parts to prevent cutting or crimping. • When folding a flat ribbon cable, never fold to a sharp crease. Sharp creases may damage the wires. • Some flat ribbon cables come pre-folded. Never change the folds on these cables. • Do not sharply bend any cable. A sharp bend can break the internal wires. • Never bend a SATA data cable tighter than a 30 mm (1.18 in) radius. • Never crease a SATA data cable. • Do not rely on components like the drive cage, power supply, or system cover to push cables down into the chassis. Removing power supply cables from the system board connectors (J13, J23, J26, and J38) follow below steps: 1. Squeeze on the top of the retaining latch attached to the cable end of the connector. 2. Grasp the cable end of the connector and pull it straight up. CAUTION: Always pull the connector - NEVER pull on the cable. Pulling on the cable could damage the cable and result in a failed power supply. Figure 5 Unplugging power cables Removal and replacement procedures 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Removal and replacement procedures
32
•
Keep cables away from major heat sources like the heat sink.
•
Do not jam cables on top of expansion cards or memory modules. Printed circuit cards are not
designed to withstand excessive pressure.
•
Keep cables clear of sliding or moveable parts to prevent cutting or crimping.
•
When folding a flat ribbon cable, never fold to a sharp crease. Sharp creases may damage the
wires.
•
Some flat ribbon cables come pre-folded. Never change the folds on these cables.
•
Do not sharply bend any cable. A sharp bend can break the internal wires.
•
Never bend a SATA data cable tighter than a 30 mm (1.18 in) radius.
•
Never crease a SATA data cable.
•
Do not rely on components like the drive cage, power supply, or system cover to push cables
down into the chassis.
Removing power supply cables from the system board connectors (J13, J23, J26, and J38) follow
below steps:
1.
Squeeze on the top of the retaining latch attached to the cable end of the connector.
2.
Grasp the cable end of the connector and pull it straight up.
CAUTION:
Always pull the connector - NEVER pull on the cable. Pulling on the cable could damage
the cable and result in a failed power supply.
Figure 5
Unplugging power cables