HP ENVY 14-j100 Maintenance and Service Guide - Page 72

Display assembly, Remove the Phillips PM2.0×3.3 screw

Get HP ENVY 14-j100 PDF manuals and user guides View all HP ENVY 14-j100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

c. RJ45 cover (see RJ45 cover on page 49) d. Security cable slot bracket (see Security cable slot bracket on page 51) e. System board (see System board on page 52) Remove the power connector cable: 1. Remove the Phillips PM2.0×3.3 screw (1) that secures the power connector cable and bracket to the top cover. 2. Remove the power connector cable bracket (2). The power connector cable bracket is available using spare part number 818117-001. 3. Remove the power connector cable (3). Reverse this procedure to install the power connector cable. Display assembly Before removing the display assembly, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the bottom cover (see Bottom cover on page 28). 5. Disconnect the battery cable from the system board (see Battery on page 38). 6. Remove the RJ45 cover (see RJ45 cover on page 49). 7. Remove the security cable slot bracket (see Security cable slot bracket on page 51). Remove the display assembly: 62 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
c.
RJ45 cover (see
RJ45 cover
on page
49
)
d.
Security cable slot bracket (see
Security cable slot bracket
on page
51
)
e.
System board (see
System board
on page
52
)
Remove the power connector cable:
1.
Remove the Phillips PM2.0×3.3 screw
(1)
that secures the power connector cable and bracket to
the top cover.
2.
Remove the power connector cable bracket
(2)
.
The power connector cable bracket is available using spare part number 818117-001.
3.
Remove the power connector cable
(3)
.
Reverse this procedure to install the power connector cable.
Display assembly
Before removing the display assembly, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
28
).
5.
Disconnect the battery cable from the system board (see
Battery
on page
38
).
6.
Remove the RJ45 cover (see
RJ45 cover
on page
49
).
7.
Remove the security cable slot bracket (see
Security cable slot bracket
on page
51
).
Remove the display assembly:
62
Chapter 6
Removal and replacement procedures for Authorized Service Provider parts