HP EVA P6550 HP P6300/P6500 EVA User Guide (5697-2486, September 2013) - Page 190

Disk In Line Exerciser cannot be stopped, Drive FW Load Abort Due

Get HP EVA P6550 PDF manuals and user guides View all HP EVA P6550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 190 highlights

Table 27 Error Messages (continued) Status code value Meaning How to correct 128 OCP Error EVA 6400/8400 only. A generic error was Ensure other OCP is on and try again. detected with the OCP interface. If the problem persists, report the error to product support. 129 Mirror Temporarily Offline The virtual disk is not mirrored to the other Ensure other controller is operative. controller. 130 Failsafe Mode Enabled Cannot perform operation because FAILSAFE Disable Failsafe mode on Group. is enabled on Group. 131 Drive FW Load Abort Due to VRaid0 Vdisk The drive firmware cannot be downloaded to the drive because it is being used for RAID0 data. One or more RAID0 virtual disks would be inoperable if the drive were to be loaded. Migrate RAID0 data to another disk group or a more protective redundancy before retrying the drive update. 132 FC Ports Unavailable There is a diagnostic problem with the indicated port. Report the error to product support. 133 Only Two Remote Relations Are Allowed Only two remote relationships are allowed. Need to reconfigure configuration to only have two remote destinations. 134 The existing drive configuration does not The Requested SRC Mode is Not support the requested SRC mode. Possible Report the error to product support. 135 This error is no longer supported. Source Group Discarded, but the Destination Group NOT Discarded Report the error to product support. 136 Invalid DRM Group Tunnel Specified This error is no longer supported. Report the error to product support. 137 Specified DRM Log Size Too Small This error is no longer supported. Report the error to product support. 138 Invalid Disk Group Specified The disk group requested for the attempted Retry command using an appropriate command is not valid. disk group identifier. 139 DRM Group is Already Read-Only Data replication group is already read-only. Disable read-only mode in group. 140 DRM Group is Already Active-Active Data replication group is already active-active. Disable active-active mode in group. 141 DILX Is Already Running The requested operation cannot be Retry command after DILX is complete. completed while Disk In Line Exerciser is in progress. 142 DILX Is Not Running Disk In Line Exerciser cannot be stopped because it is not running. No corrective action required. 143 Invalid User Defined Log Size Invalid user defined log size. Reissue operation with a valid log size 144 Invalid data replication group identifier Invalid Second Handle Paramed specified. Retry the command with an existing data replication group. 145 DRM Group Already Auto Suspended Data replication group already auto suspended. Unsuspend group and reissue operation. 190 Error messages

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
Table 27 Error Messages
(continued)
How to correct
Meaning
Status code value
Ensure other OCP is on and try again.
If the problem persists, report the error
to product support.
EVA 6400/8400 only. A generic error was
detected with the OCP interface.
128
OCP Error
Ensure other controller is operative.
The virtual disk is not mirrored to the other
controller.
129
Mirror Temporarily Offline
Disable Failsafe mode on Group.
Cannot perform operation because FAILSAFE
is enabled on Group.
130
Failsafe Mode Enabled
Migrate RAID0 data to another disk
group or a more protective
The drive firmware cannot be downloaded
to the drive because it is being used for
131
Drive FW Load Abort Due to
VRaid0 Vdisk
redundancy before retrying the drive
update.
RAID0 data. One or more RAID0 virtual
disks would be inoperable if the drive were
to be loaded.
Report the error to product support.
There is a diagnostic problem with the
indicated port.
132
FC Ports Unavailable
Need to reconfigure configuration to
only have two remote destinations.
Only two remote relationships are allowed.
133
Only Two Remote Relations Are
Allowed
Report the error to product support.
The existing drive configuration does not
support the requested SRC mode.
134
The Requested SRC Mode is Not
Possible
Report the error to product support.
This error is no longer supported.
135
Source Group Discarded, but the
Destination Group NOT
Discarded
Report the error to product support.
This error is no longer supported.
136
Invalid DRM Group Tunnel
Specified
Report the error to product support.
This error is no longer supported.
137
Specified DRM Log Size Too
Small
Retry command using an appropriate
disk group identifier.
The disk group requested for the attempted
command is not valid.
138
Invalid Disk Group Specified
Disable read-only mode in group.
Data replication group is already read-only.
139
DRM Group is Already
Read-Only
Disable active-active mode in group.
Data replication group is already
active-active.
140
DRM Group is Already
Active-Active
Retry command after DILX is complete.
The requested operation cannot be
completed while Disk In Line Exerciser is in
progress.
141
DILX Is Already Running
No corrective action required.
Disk In Line Exerciser cannot be stopped
because it is not running.
142
DILX Is Not Running
Reissue operation with a valid log size
Invalid user defined log size.
143
Invalid User Defined Log Size
Retry the command with an existing
data replication group.
Invalid data replication group identifier
specified.
144
Invalid Second Handle Paramed
Unsuspend group and reissue
operation.
Data replication group already auto
suspended.
145
DRM Group Already Auto
Suspended
190
Error messages