HP EVA P6550 HP P6300/P6500 EVA User Guide (5697-2486, September 2013) - Page 65

Fabric setup and zoning, Oracle StorEdge Traffic Manager (MPxIO)/Oracle Storage Multipathing

Get HP EVA P6550 PDF manuals and user guides View all HP EVA P6550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

hba1-SCSI-target-id-31-fibre-channel-port-name="50001fe10027093b"; NOTE: Replace the WWPNs in the example with the WWPNs of your array ports. 6. If the qla2300 driver is version 4.13.01 or earlier, for each LUN that users will access, add an entry to the /kernel/drv/sd.conf file: name="sd" class="scsi" target=20 lun=1; name="sd" class="scsi" target=21 lun=1; name="sd" class="scsi" target=30 lun=1; name="sd" class="scsi" target=31 lun=1; If LUNs are preconfigured in the/kernel/drv/sd.conf file, after changing the configuration file, use the devfsadm command to perform LUN rediscovery. 7. If the qla2300 driver is version 4.15 or later, verify that the following or a similar entry is present in the /kernel/drv/sd.conf file: name="sd" parent="qla2300" target=2048; To perform LUN rediscovery after configuring the LUNs, use the following command: /opt/QLogic_Corporation/drvutil/qla2300/qlreconfig -d qla2300 -s 8. Reboot the server to implement the changes to the configuration files. NOTE: The qla2300 driver is not supported for Oracle StorEdge Traffic Manager/Oracle Storage Multipathing. To configure a QLogic FCA using the Oracle SAN driver stack, see "Configuring FCAs with the Oracle SAN driver stack" (page 62). Fabric setup and zoning To set up the fabric and zoning: 1. Verify that the Fibre Channel cable is connected and firmly inserted at the array ports, host ports, and SAN switch. 2. Through the Telnet connection to the switch or Switch utilities, verify that the WWN of the EVA ports and FCAs are present and online. 3. Create a zone consisting of the WWNs of the EVA ports and FCAs, and then add the zone to the active switch configuration. 4. Enable and then save the new active switch configuration. NOTE: There are variations in the steps required to configure the switch between different vendors. For more information, see the HP SAN Design Reference Guide, available for downloading on the HP website: http://www.hp.com/go/sandesign. Oracle StorEdge Traffic Manager (MPxIO)/Oracle Storage Multipathing Oracle StorEdge Traffic Manager (MPxIO)/Oracle Storage Multipathing can be used for FCAs configured with the Oracle SAN driver and depending on the operating system version, architecture (SPARC/x86), and patch level installed. For configuration details, see the HP StorageWorks MPxIO application notes, available on the HP support website: http://www.hp.com/support/manuals. NOTE: MPxIO is included in the SPARC and x86 Oracle SAN driver. A separate installation of MPxIO is not required. In the Search products box, enter MPxIO, and then click the search symbol. Select the application notes from the search results. Oracle Solaris 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
hba1-SCSI-target-id-31-fibre-channel-port-name="50001fe10027093b";
NOTE:
Replace the WWPNs in the example with the WWPNs of your array ports.
6.
If the qla2300 driver is version 4.13.01 or earlier, for each LUN that users will access, add
an entry to the
/kernel/drv/sd.conf
file:
name="sd" class="scsi" target=20 lun=1;
name="sd" class="scsi" target=21 lun=1;
name="sd" class="scsi" target=30 lun=1;
name="sd" class="scsi" target=31 lun=1;
If LUNs are preconfigured in the
/kernel/drv/sd.conf
file, after changing the configuration
file, use the
devfsadm
command to perform LUN rediscovery.
7.
If the qla2300 driver is version 4.15 or later, verify that the following or a similar entry is
present in the
/kernel/drv/sd.conf
file:
name="sd" parent="qla2300" target=2048;
To perform LUN rediscovery after configuring the LUNs, use the following command:
/opt/QLogic_Corporation/drvutil/qla2300/qlreconfig
–
d qla2300 -s
8.
Reboot the server to implement the changes to the configuration files.
NOTE:
The qla2300 driver is
not
supported for Oracle StorEdge Traffic Manager/Oracle Storage
Multipathing. To configure a QLogic FCA using the Oracle SAN driver stack, see
“Configuring
FCAs with the Oracle SAN driver stack” (page 62)
.
Fabric setup and zoning
To set up the fabric and zoning:
1.
Verify that the Fibre Channel cable is connected and firmly inserted at the array ports, host
ports, and SAN switch.
2.
Through the Telnet connection to the switch or Switch utilities, verify that the WWN of the
EVA ports and FCAs are present and online.
3.
Create a zone consisting of the WWNs of the EVA ports and FCAs, and then add the zone
to the active switch configuration.
4.
Enable and then save the new active switch configuration.
NOTE:
There are variations in the steps required to configure the switch between different
vendors. For more information, see the
HP SAN Design Reference Guide
, available for downloading
on the HP website:
h
t
tp://w
w
w
.hp
.co
m/go/s
ande
si
gn
.
Oracle StorEdge Traffic Manager (MPxIO)/Oracle Storage Multipathing
Oracle StorEdge Traffic Manager (MPxIO)/Oracle Storage Multipathing can be used for FCAs
configured with the Oracle SAN driver and depending on the operating system version, architecture
(SPARC/x86), and patch level installed. For configuration details, see the
HP StorageWorks MPxIO
application notes
, available on the HP support website:
h
t
tp://w
w
w
.hp
.co
m/su
ppo
r
t/man
uals
.
NOTE:
MPxIO is included in the SPARC and x86 Oracle SAN driver. A separate installation of
MPxIO is not required.
In the
Search products
box, enter
MPxIO
, and then click the search symbol. Select the
application notes from the search results.
Oracle Solaris
65