HP Integrity Superdome 2 8/16 HP Smart Update Manager 5.3 User Guide - Page 37

Description, Overriding errors, Reboot options, Simulating HP SUM, Targets

Get HP Integrity Superdome 2 8/16 PDF manuals and user guides View all HP Integrity Superdome 2 8/16 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Overriding errors /oa_name and /oa_password Reboot options /r[eboot] /reboot_message "reboot message" /reboot_delay timeout_in_secs /reboot_always Simulating HP SUM /dryrun Targets /user or /username /passwd /target "netAddress" Description This command is for HP Integrity servers only. Use these arguments if you do not use the /partition_only argument. If you do not enter the selections, then the update will display and error and exit. This command is for HP Integrity servers only. Description If the following conditions are met, this argument causes the server (or host server in a remote installation) to reboot: • The /reboot option is selected or given as a command-line argument. • All components selected for installation are successfully installed. • At least one of the installed components requires a reboot to complete its installation. Displays the specified reboot message on remote consoles connected to the server that you want to reboot. You must use this argument with the /reboot option, or the argument is ignored. Delays the reboot of the server for the length of time that the timeout_in_seconds variable specifies. You must use this argument with the /reboot option, or the argument is ignored. Acceptable values are between 15 and 3600. • The default timeout value is 15 seconds for Microsoft Windows operating systems and 60 seconds for Linux. • For Linux, the reboot delay time is converted from seconds to minutes, and any value under a full minute (59 seconds or less) rounds to the next minute. If the following conditions are met, this argument forces the server to reboot: • The /reboot_always option is selected or given as a command-line argument. • All components selected for installation are successfully installed. Description Simulates the installation for a test run. Nothing is installed. Description Use this argument to log in to the remote targets by using the user ID. For the OA target, use the /oa_username argument. Use this argument to use this password for the user ID specified in the /user parameter (except for the OA target). The password is used to log in to remote targets. For the OA target, use the /oa_password argument. This is the IP address or the DNS name of a remote host, which can be a remote server, remote iLO NIC port, Virtual Command-line interface 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
Description
Overriding errors
This command is for HP Integrity servers only.
Use these arguments if you do not use the
/partition_only
argument. If you do not enter the
selections, then the update will display and error and exit.
/oa_name
and
/oa_password
This command is for HP Integrity servers only.
Description
Reboot options
If the following conditions are met, this argument causes
the server (or host server in a remote installation) to reboot:
/r[eboot]
•
The
/reboot
option is selected or given as a
command-line argument.
•
All components selected for installation are successfully
installed.
•
At least one of the installed components requires a
reboot to complete its installation.
Displays the specified reboot message on remote consoles
connected to the server that you want to reboot. You must
/reboot_message "reboot message"
use this argument with the
/reboot
option, or the
argument is ignored.
Delays the reboot of the server for the length of time that
the
timeout_in_seconds
variable specifies. You must
/reboot_delay timeout_in_secs
use this argument with the
/reboot
option, or the
argument is ignored. Acceptable values are between 15
and 3600.
•
The default timeout value is 15 seconds for Microsoft
Windows operating systems and 60 seconds for Linux.
•
For Linux, the reboot delay time is converted from
seconds to minutes, and any value under a full minute
(59 seconds or less) rounds to the next minute.
If the following conditions are met, this argument forces
the server to reboot:
/reboot_always
•
The
/reboot_always
option is selected or given as
a command-line argument.
•
All components selected for installation are successfully
installed.
Description
Simulating HP SUM
Simulates the installation for a test run. Nothing is installed.
/dryrun
Description
Targets
Use this argument to log in to the remote targets by using
the user ID. For the OA target, use the
/oa_username
argument.
/user
<username>
or
/username
<username>
Use this argument to use this password for the user ID
specified in the
/user
parameter (except for the OA
/passwd
<password>
target). The password is used to log in to remote targets.
For the OA target, use the
/oa_password
argument.
This is the IP address or the DNS name of a remote host,
which can be a remote server, remote iLO NIC port, Virtual
/target
“
netAddress
”
Command-line interface
37