HP LH4r HP Netserver LC 3 User Guide - Page 11

Install Additional Memory

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Chapter 1 Installation Overview c. Push the top cover back, and lift it off. The Technical Reference Label is inside the top cover. 5. If you are installing any accessory boards or additional mass storage devices (other than hot-swap disk drive modules), also remove the side cover farthest from the system board (See Figure 1-1, Step D.): a. Grasp the two tabs at the top of the side cover. b. Pull upward and outward to lift the side cover off. CAUTION Handle the side cover only by its top and bottom edges to avoid damaging the EMI spring fingers inside its side edges. Install Additional Memory CAUTION The LC 3 uses 100 MHz SDRAM DIMMs, which are electrically different from the EDO memory modules used with earlier models. (Even though the EDO DIMM from earlier models does fit in the DIMM sockets, it does not function.) Do not install EDO DIMMs from previous models in the LC 3. CAUTION Use only DIMMs acquired from HP. Refer to the following for a list of qualified DIMMs: • Technical Reference Label inside the HP NetServer top cover • HP Order Assistant on the HP Web Site at http://www.hp.com/go/netserver • Information Assistant on the HP Navigator CD-ROM • HP Customer Service When handling DIMMs, observe antistatic precautions to avoid damage. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Chapter 1
Installation Overview
5
c.
Push the top cover back, and lift it off. The Technical Reference Label
is inside the top cover.
5.
If you are installing any accessory boards or additional mass storage
devices (other than hot-swap disk drive modules), also remove the side
cover farthest from the system board (See Figure 1-1, Step D.):
a.
Grasp the two tabs at the top of the side cover.
b.
Pull upward and outward to lift the side cover off.
CAUTION
Handle the side cover only by its top and bottom edges to
avoid damaging the EMI spring fingers inside its side edges.
Install Additional Memory
CAUTION
The LC 3 uses 100 MHz SDRAM DIMMs, which are
electrically different from the EDO memory modules used
with earlier models. (Even though the EDO DIMM from
earlier models does fit in the DIMM sockets, it does not
function.) Do not install EDO DIMMs from previous models
in the LC 3.
CAUTION
Use only DIMMs acquired from HP. Refer to the following
for a list of qualified DIMMs:
•
Technical Reference Label inside the HP NetServer top
cover
•
HP Order Assistant on the HP Web Site at
•
Information Assistant on the HP Navigator CD-ROM
•
HP Customer Service
When handling DIMMs, observe antistatic precautions to
avoid damage.