HP LH4r HP Netserver LC 3 User Guide - Page 55

No Error Messages Displayed

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Chapter 6 Troubleshooting Message Operating system not found Keyboard error Mouse error Incorrect System Configuration Corrective Action Check whether the drive from which you are booting has the power and SCSI flat cables connected. Verify that the SCSI cable is securely plugged into the SCSI controller board. Narrow (50-pin) SCSI devices require the wideto-narrow SCSI adapter with the white body on the SCSI cable. Check that the boot device is enabled in the Hardware Security submenu under the Security menu of the Setup utility. If possible, check the drive by moving it to another system. If the problem persists, contact your HP support organization. Verify that the boot device has an operating system installed. Check that the keyboard is connected to the correct connector (not the mouse connector) at the rear of the system. Replace the keyboard. If the problem persists, contact your HP support organization. Check that the mouse is connected to the correct connector (not the keyboard connector) at the rear of the system. Replace the mouse. If the problem persists, contact your HP support organization. Press the F2 key to run the Setup utility. Change settings as required. Press the F10 function key to exit, and answer "Yes" to save the changes. No Error Messages Displayed If a POST error is detected before video display starts, a beep error message may be generated. If so, refer to the list of Beep Codes in Information Assistant. General Checks 1. All external cables and power cables are firmly plugged in. 2. The power outlet is working. 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Chapter 6
Troubleshooting
49
Message
Corrective Action
Operating system
not found
Check whether the drive from which you are booting has
the power and SCSI flat cables connected. Verify that the
SCSI cable is securely plugged into the SCSI controller
board. Narrow (50-pin) SCSI devices require the wide-
to-narrow SCSI adapter with the white body on the SCSI
cable.
Check that the boot device is enabled in the Hardware
Security submenu under the Security menu of the Setup
utility. If possible, check the drive by moving it to
another system. If the problem persists, contact your HP
support organization.
Verify that the boot device has an operating system
installed.
Keyboard error
Check that the keyboard is connected to the correct
connector (
not the mouse connector
) at the rear of the
system.
Replace the keyboard. If the problem persists, contact
your HP support organization.
Mouse error
Check that the mouse is connected to the correct
connector (
not the keyboard connector
) at the rear of
the system.
Replace the mouse. If the problem persists, contact your
HP support organization.
Incorrect System
Configuration
Press the F2 key to run the Setup utility. Change settings
as required. Press the F10 function key to exit, and
answer "Yes" to save the changes.
No Error Messages Displayed
If a POST error is detected before video display starts, a beep error message may
be generated. If so, refer to the list of Beep Codes in Information Assistant.
General Checks
1.
All external cables and power cables are firmly plugged in.
2.
The power outlet is working.