HP LH4r HP Netserver LC 3 User Guide - Page 20

Reserve Resources for ISA Non-Plug-and-Play Board, Run Configuration Assistant and Installation

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Chapter 1 Installation Overview 2. From the Options menu, select one of the following: ◊ Configure/View Host Adapter Settings: Select this option to configure or view SCSI bus interface definitions, boot device options, SCSI configurations, and advanced configuration options. ◊ SCSI Disk Utilities: Select this option to format disks or verify disk media. 3. Use the arrow keys to move the cursor, press ENTER to select an option, and press ESC to exit. Reserve Resources for ISA Non-Plug-and-Play Board If you have installed an ISA non-plug-and play accessory board, you must reserve system resources for it. Turn on the monitor and the HP NetServer, and start the Setup utility by pressing the F2 key when Press to enter SETUP appears on the boot screen. NOTE Pressing the F2 key when prompted should start the Setup utility. For some ISA boards, the Setup utility will not start, and you must remove the ISA board, use the Setup utility to reserve system resources for the ISA board, and then replace the ISA board. Use the Setup utility to allocate system resources to the ISA non-plug-and-play accessory board. Refer to the "Installing ISA Non-Plug-and-Play Boards" in Chapter 4, "Accessories," for instructions. Run Configuration Assistant and Installation Assistant Turn on the monitor and the HP NetServer, and insert the HP Navigator CD-ROM into the drive. Turn the power off, wait 10 seconds, and turn the power on again. If the system fails to start, follow the instructions on the screen. 1. When HP Navigator starts, you may need to set the language and the time and date. Follow the onscreen instructions. You can also change the language of the BIOS when prompted. 2. Go to the HP Navigator Main Menu and select "Configuration and Installation Assistant." 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Chapter 1
Installation Overview
14
2.
From the Options menu, select one of the following:
◊
Configure/View Host Adapter Settings:
Select this option to
configure or view SCSI bus interface definitions, boot device options,
SCSI configurations, and advanced configuration options.
◊
SCSI Disk Utilities:
Select this option to format disks or verify disk
media.
3.
Use the arrow keys to move the cursor, press ENTER to select an option,
and press ESC to exit.
Reserve Resources for ISA Non-Plug-and-Play Board
If you have installed an ISA non-plug-and play accessory board, you must reserve
system resources for it. Turn on the monitor and the HP NetServer, and start the
Setup utility by pressing the F2 key when
Press <F2> to enter SETUP
appears on the boot screen.
NOTE
Pressing the F2 key when prompted should start the Setup
utility. For some ISA boards, the Setup utility will not start,
and you must remove the ISA board, use the Setup utility to
reserve system resources for the ISA board, and then replace
the ISA board.
Use the Setup utility to allocate system resources to the ISA non-plug-and-play
accessory board. Refer to the "Installing ISA Non-Plug-and-Play Boards" in
Chapter 4, "Accessories," for instructions.
Run Configuration Assistant and Installation Assistant
Turn on the monitor and the HP NetServer, and insert the HP Navigator
CD-ROM into the drive. Turn the power off, wait 10 seconds, and turn the power
on again. If the system fails to start, follow the instructions on the screen.
1.
When HP Navigator starts, you may need to set the language and the time
and date. Follow the onscreen instructions. You can also change the
language of the BIOS when prompted.
2.
Go to the HP Navigator Main Menu and select "Configuration and
Installation Assistant."