HP LH4r HP Netserver LC 3 User Guide - Page 39

I/O Resources, Interrupt Resources, without, Exit Discarding Changes

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Chapter 4 Accessories 11. Use the up and down arrow keys to select the DMA channel that corresponds to the DMA channel required for the ISA board you are installing, and press the + or - key on the keypad to reserve it. Reserve all DMA channels needed for the board. 12. When all the necessary DMA channels are reserved, press ESC to return to the ISA non-Plug-and-Play Devices submenu. 13. Use the up and down arrow keys to highlight I/O Resources, and press ENTER to select that submenu. 14. Use the up and down arrow keys to highlight the I/O port block that corresponds to the I/O port range required by the board you are installing, and press the + or - key on the keypad to reserve that block. If the I/O port range required for the board spans two or more blocks shown on the screen, reserve all blocks required by the board. If the I/O port range required for the board is less than one block, select the whole block that contains the range. 15. When all the necessary I/O port blocks are reserved, press ESC to return to the ISA non-Plug-and-Play Devices submenu. 16. Use the up and down arrow keys to highlight Interrupt Resources, and press ENTER to select that submenu. 17. Use the up and down arrow keys to highlight the IRQ that corresponds to the IRQ required for the board you are installing, and press the + or - key on the keypad to reserve that IRQ. Reserve all IRQs needed for the board. 18. When all the necessary IRQs and other resources are reserved, press the F10 function key to save and exit. 19. In the Setup Confirmation dialog box, press ENTER to answer "Yes" to the question, "Save configuration and exit now?" The HP NetServer will reboot. NOTE If you change your mind and want to exit the Setup utility without making the changes you have selected, press ESC once or twice to return to the Setup Utility menu. Use the right arrow key to select the Exit menu. Use the down arrow key to highlight Exit Discarding Changes. In the Setup Warning dialog box, use the spacebar or right arrow key to highlight No. Press ENTER to answer "No" to the question, "Configuration has not been saved! Save before exiting?" 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Chapter 4
Accessories
33
11.
Use the up and down arrow keys to select the DMA channel that
corresponds to the DMA channel required for the ISA board you are
installing, and press the + or - key on the keypad to reserve it. Reserve all
DMA channels needed for the board.
12.
When all the necessary DMA channels are reserved, press ESC to return
to the ISA non-Plug-and-Play Devices submenu.
13.
Use the up and down arrow keys to highlight
I/O Resources
, and press
ENTER to select that submenu.
14.
Use the up and down arrow keys to highlight the I/O port block that
corresponds to the I/O port range required by the board you are installing,
and press the + or - key on the keypad to reserve that block. If the I/O port
range required for the board spans two or more blocks shown on the
screen, reserve all blocks required by the board. If the I/O port range
required for the board is less than one block, select the whole block that
contains the range.
15.
When all the necessary I/O port blocks are reserved, press ESC to return
to the ISA non-Plug-and-Play Devices submenu.
16.
Use the up and down arrow keys to highlight
Interrupt Resources
, and
press ENTER to select that submenu.
17.
Use the up and down arrow keys to highlight the IRQ that corresponds to
the IRQ required for the board you are installing, and press the + or - key
on the keypad to reserve that IRQ. Reserve all IRQs needed for the board.
18.
When all the necessary IRQs and other resources are reserved, press the
F10 function key to save and exit.
19.
In the Setup Confirmation dialog box, press ENTER to answer "Yes" to
the question, "Save configuration and exit now?" The HP NetServer will
reboot.
NOTE
If you change your mind and want to exit the Setup utility
without
making the changes you have selected, press ESC
once or twice to return to the Setup Utility menu. Use the right
arrow key to select the
Exit
menu. Use the down arrow key to
highlight
Exit Discarding Changes
. In the Setup Warning
dialog box, use the spacebar or right arrow key to highlight
No
. Press ENTER to answer "No" to the question,
"Configuration has not been saved! Save before exiting?"