HP LH4r HP Netserver LC 3 User Guide - Page 57

Clearing the System Configuration

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Chapter 6 Troubleshooting ◊ Check that all DIMMs are HP-supplied and are seated properly. The boot screen provides information on the installed DIMMs. ◊ Check all internal cabling and connections. ◊ If you have changed any switches on the system board, check that they are properly set. 5. Lower the system board if it was raised and lower the retaining latches simultaneously. Replace the covers and front bezel, and connect all cables. 6. Turn on the display and HP NetServer. 7. If the HP NetServer still does not work: ◊ Repeat steps 1, 2, and 3 of this section. ◊ Remove all accessories, except the primary boot hard disk drive. ◊ Replace the covers and connect all cables. ◊ Turn on the display and the HP NetServer. ◊ If the HP NetServer now works, replace the boards and accessories one at a time to determine which one is causing the problem. Clearing the System Configuration You may need to clear the system configuration if the configuration has been corrupted by a program, or if incorrect settings made in the Setup utility have made the display unreadable. 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Chapter 6
Troubleshooting
51
◊
Check that all DIMMs are HP-supplied and are seated properly. The
boot screen provides information on the installed DIMMs.
◊
Check all internal cabling and connections.
◊
If you have changed any switches on the system board, check that they
are properly set.
5.
Lower the system board if it was raised and lower the retaining latches
simultaneously. Replace the covers and front bezel, and connect all cables.
6.
Turn on the display and HP NetServer.
7.
If the HP NetServer still does not work:
◊
Repeat steps 1, 2, and 3 of this section.
◊
Remove all accessories, except the primary boot hard disk drive.
◊
Replace the covers and connect all cables.
◊
Turn on the display and the HP NetServer.
◊
If the HP NetServer now works, replace the boards and accessories one
at a time to determine which one is causing the problem.
Clearing the System Configuration
You may need to clear the system configuration if the configuration has been
corrupted by a program, or if incorrect settings made in the Setup utility have
made the display unreadable.