HP LH4r HP Netserver LC 3 User Guide - Page 17

Install Additional Mass Storage Devices, Replace All Covers and Connect All Cables

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Chapter 1 Installation Overview e. Configuration Advisor displays the Configuration Advisories. You can print them out by saving them to disk (diskette) and later printing out from the diskette. Read the documentation supplied with the accessory boards. If you are installing an ISA non-plug-and-play board, write down the switch and jumper settings and all system resource requirements (such as memory range, I/O port range, DMA channel, and IRQ level). Refer to these notes when you allocate system resources to the ISA non-plug-and-play board when you configure the HP NetServer. Install Additional Mass Storage Devices Certain mass storage configurations may require additional cables or adapters. For part numbers for HP cables, adapters, and trays, and configuration information, see Information Assistant on the HP Navigator CD-ROM. For new products, you can use Order Assistant on the HP Web Site at http://www.hp.com/go/netserver. Click the hot spot "Ordering NetServers" and choose your desired option. Replace All Covers and Connect All Cables Refer to Figure 1-6 and replace all covers. CAUTION Covers are necessary for proper air flow through the system. Please replace ALL covers before operating the HP NetServer, even for a short time. Otherwise, overheating can damage processors, boards, and mass storage devices. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Chapter 1
Installation Overview
11
e.
Configuration Advisor displays the Configuration Advisories. You can
print them out by saving them to disk (diskette) and later printing out
from the diskette.
Read the documentation supplied with the accessory boards. If you are installing
an ISA non-plug-and-play board, write down the switch and jumper settings and
all system resource requirements (such as memory range, I/O port range, DMA
channel, and IRQ level). Refer to these notes when you allocate system resources
to the ISA non-plug-and-play board when you configure the HP NetServer.
Install Additional Mass Storage Devices
Certain mass storage configurations may require additional cables or adapters.
For part numbers for HP cables, adapters, and trays, and configuration
information, see Information Assistant on the HP Navigator CD-ROM. For new
products, you can use Order Assistant on the HP Web Site at
. Click the hot spot "Ordering NetServers" and
choose your desired option.
Replace All Covers and Connect All Cables
Refer to Figure 1-6 and replace all covers.
CAUTION
Covers are necessary for proper air flow through the system.
Please replace ALL covers before operating the HP
NetServer, even for a short time. Otherwise, overheating can
damage processors, boards, and mass storage devices.