HP LH4r HP Netserver LC 3 User Guide - Page 59

Hardware Problems

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter 6 Troubleshooting 3. Plug in the power cord, and turn on power to the HP NetServer. The message Configuration has been cleared, set Clear Config switch to the OFF position before rebooting is displayed. 4. Turn off power to the HP NetServer, and unplug the power cord. 5. Return switch 5 on the system board to the OFF position. 6. Replace the system board, the top cover, and the front bezel, and plug in the power cord. 7. Turn on power to the HP NetServer. The error message 0012-34 : Incorrect System Configuration may be displayed. If the error message above is displayed, it is followed by the explanation The BIOS has detected a serious problem that prevents your PC from booting This is normal. 8. Press the F2 key to run the Setup utility. 9. Make any configuration changes that are required. 10. Press the F10 function key and answer "Yes" to save the configuration and exit the Setup utility. Hardware Problems This section describes what to do if you have problems with your display, mass storage devices, printer, accessory boards, keyboard, or mouse. The Display Does Not Work NOTE If the HP NetServer has a large amount of memory installed, it may take one minute for the first screen to display. 1. If nothing is displayed on the screen, but the computer starts and, the keyboard, flexible disk drive, other disk drives, and other peripheral devices seem to operate properly, do the following: ◊ Check that the monitor is plugged in and power is turned on. 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Chapter 6
Troubleshooting
53
3.
Plug in the power cord, and turn on power to the HP NetServer. The
message
Configuration has been cleared, set Clear Config
switch to the OFF position before rebooting
is displayed.
4.
Turn off power to the HP NetServer, and unplug the power cord.
5.
Return switch 5 on the system board to the OFF position.
6.
Replace the system board, the top cover, and the front bezel, and plug in
the power cord.
7.
Turn on power to the HP NetServer. The error message
0012-34 : Incorrect System Configuration
may be displayed. If the error message above is displayed, it is followed by
the explanation
The BIOS has detected a serious problem that
prevents your PC from booting
This is normal.
8.
Press the F2 key to run the Setup utility.
9.
Make any configuration changes that are required.
10.
Press the F10 function key and answer "Yes" to save the configuration and
exit the Setup utility.
Hardware Problems
This section describes what to do if you have problems with your display, mass
storage devices, printer, accessory boards, keyboard, or mouse.
The Display Does Not Work
NOTE
If the HP NetServer has a large amount of memory installed, it
may take one minute for the first screen to display.
1.
If nothing is displayed on the screen, but the computer starts and, the
keyboard, flexible disk drive, other disk drives, and other peripheral
devices seem to operate properly, do the following:
◊
Check that the monitor is plugged in and power is turned on.