HP LH4r HP Netserver LC 3 User Guide - Page 46

cables. Doing so prevents any possibility for electrical burns

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Chapter 5 Installation in Rack (Optional) 9. Insert one M4 button-headed screw through the filler panel and into the threaded insert in the sliding shelf of the base assembly. 10. Insert one cosmetic screw through the flange on the left sliding shelf and into the rack nut you positioned there in step 3. 11. Prepare each HP NetServer LC 3 for mounting in the rack. WARNING Extend the anti-tip foot from the front lower section of the rack before placing the LC 3 on the base assembly. Also ensure the leveler screws at each corner are in firm contact with the floor. ◊ Turn off and disconnect the HP NetServer from power and telephone. ◊ Remove the covers of the LC 3 as discussed in Chapter 1, "Remove the Covers." WARNING Always disconnect the power cord and unplug telephone cables. Doing so prevents any possibility for electrical burns or exposure to high energy levels. 12. Be sure the anti-tip foot and the leveler screws are fully extended to prevent the rack from rolling away or tipping over. Get help to lift the NetServer onto the right side of the extended base unit, as shown in Figures 5-4 and 5-5. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Chapter 5
Installation in Rack (Optional)
40
9.
Insert one M4 button-headed screw through the filler panel and into the
threaded insert in the sliding shelf of the base assembly.
10.
Insert one cosmetic screw through the flange on the left sliding shelf and
into the rack nut you positioned there in step 3.
11.
Prepare each HP NetServer LC 3 for mounting in the rack.
WARNING
Extend the anti-tip foot from the front lower section of the
rack before placing the LC 3 on the base assembly. Also
ensure the leveler screws at each corner are in firm contact
with the floor.
◊
Turn off and disconnect the HP NetServer from power and telephone.
◊
Remove the covers of the LC 3 as discussed in Chapter 1, "Remove the
Covers."
WARNING
Always disconnect the power cord and unplug telephone
cables. Doing so prevents any possibility for electrical burns
or exposure to high energy levels.
12.
Be sure the anti-tip foot and the leveler screws are fully extended to
prevent the rack from rolling away or tipping over. Get help to lift the
NetServer onto the right side of the extended base unit, as shown in
Figures 5-4 and 5-5.