HP LH4r HP Netserver LC 3 User Guide - Page 25

Novell NetWare / IntranetWare or Microsoft Windows NT Server, or

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Chapter 2 HP Navigator ◊ Select No for manual NOS installation. Perform a manual NOS installation if you are installing a NOS other than certain versions of Novell NetWare / IntranetWare or Microsoft Windows NT Server, or if you have replaced any HP components. • View Configuration Advisories: Read the configuration advisories, and print them out if necessary. You can change your hardware at this time to conform to the advisories. • Configure Remote Management: This utility configures the Integrated Remote Assistant device for improved remote management. It enables remote, dial-up server management. To configure Integrated Remote Assistant, select Configure Remote Management on the Configure Remote Management screen. • Show System Information: Use this screen to display information about standard and accessory boards and devices in the system, as well as the used and available system resources. ◊ Select View System Information on the Show System Information screen to display information about standard and accessory boards and devices in the system. ◊ Select View Resources on the Show System Information screen to display used and available system resources, such as memory ranges, I/O port ranges, DMA channels, and interrupt (IRQ) levels. • Configure Disk Array: If you have an HP disk array, you must configure it with the disk array utility. Select Execute on the Configure Disk Array screen to start the disk array utility. • Install Utility Partition: This step creates a utility partition on the server hard disk where HP Navigator will copy Diagnostic Assistant, the BIOS update utility, the event log report utility, the disk array utility, the Network Interface Card (NIC) configuration utility, the Remote Assistant utilities, troubleshooting utilities, and other utilities. It is not available for SCO UNIX. Select Execute on the Install Utility Partition screen. • Execute Card Utilities: When Configuration Assistant detects installed boards for which there are additional configuration utilities on the HP Navigator CD-ROM, you can execute these utilities to complete the configuration of the boards by selecting Execute on the Execute Card Utilities screen. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Chapter 2
HP Navigator
19
◊
Select
No
for manual NOS installation. Perform a manual NOS
installation if
you are installing a NOS other than certain versions of
Novell NetWare / IntranetWare or Microsoft Windows NT Server, or
if you have replaced any HP components.
•
View Configuration Advisories:
Read the configuration advisories, and
print them out if necessary. You can change your hardware at this time to
conform to the advisories.
•
Configure Remote Management:
This utility configures the Integrated
Remote Assistant device for improved remote management. It enables
remote, dial-up server management. To configure Integrated Remote
Assistant, select
Configure Remote Management
on the Configure
Remote Management screen.
•
Show System Information:
Use this screen to display information about
standard and accessory boards and devices in the system, as well as the
used and available system resources.
◊
Select
View System Information
on the Show System Information
screen to display information about standard and accessory boards and
devices in the system.
◊
Select
View Resources
on the Show System Information screen to
display used and available system resources, such as memory ranges,
I/O port ranges, DMA channels, and interrupt (IRQ) levels.
•
Configure Disk Array:
If you have an HP disk array, you must configure
it with the disk array utility. Select
Execute
on the Configure Disk Array
screen to start the disk array utility.
•
Install Utility Partition:
This step creates a utility partition on the server
hard disk where HP Navigator will copy Diagnostic Assistant, the BIOS
update utility, the event log report utility, the disk array utility, the
Network Interface Card (NIC) configuration utility, the Remote Assistant
utilities, troubleshooting utilities, and other utilities. It is not available for
SCO UNIX. Select
Execute
on the Install Utility Partition screen.
•
Execute Card Utilities:
When Configuration Assistant detects installed
boards for which there are additional configuration utilities on the HP
Navigator CD-ROM, you can execute these utilities to complete the
configuration of the boards by selecting
Execute
on the Execute Card
Utilities screen.