Home » HP Manuals » Multifunction Devices » HP M4345 » Manual Viewer

HP M4345 User Guide - Page 198

The Digital Sending Service at <IP, TOO MANY S IN JOB TO STAPLE - mfp service manual

UPC - 882780548619

Add to My Manuals
Save this manual to your list of manuals

Page 198 highlights

Table 11-1 Control-panel messages (continued) Control panel message Description Recommended action PIN is incorrect. Please enter a 4-digit number. The PIN format is incorrect. Type the 4-digit PIN. PIN is incorrect. Please re-enter PIN. The PIN was typed incorrectly. Retype the PIN. Please turn device off and install hard disk. The requested job requires a hard disk, but Turn the MFP off and install a hard disk. the MFP does not have a hard disk installed. See Order parts, accessories, and supplies. Reattach output bin The standard output bin was detached when the MFP was turned on, or the cable on the stapler/stacker or the 3-bin mailbox is not connected to the MFP. Turn the MFP off. If you are using the stapler/stacker or the 3-bin mailbox, make sure that the cable is connected to the MFP. Reattach the output bin, and then turn the MFP on. Observe the LED on the output device. If it is flashing or amber, see Solve general device problems. Reinsert duplexer The duplexer has been removed and must Reinsert the duplexer in the MFP. be reinstalled. Reinstall output device The output device has been removed or is not attached. Make sure the output bin, 3-bin mailbox, or stapler/stacker is correctly installed on the MFP. Replace cartridge The print cartridge has reached the end of its life. Printing cannot continue. Replace the print cartridge. To order a new print cartridge, see Order parts, accessories, and supplies. Replace staple cartridge The stapler is out of staples. Replace the staple cartridge. For information about replacing the staple cartridge see Order parts, accessories, and supplies. SANITIZING DISK % COMPLETE Do The hard disk is being cleaned. not power off Contact the network administrator. SCAN FAILURE Press 'Start' to rescan The scan was unsuccessful and the document needs to be rescanned. If necessary, reposition the document to rescan it, and then press Start. SMTP Gateway The SMTP gateway has exceeded a time out value. Verify the e-mail server address. See Solve e-mail problems. Contact the network administrator. STAPLER LOW ON STAPLES Fewer than 20 staples remain in the staple cartridge. Printing continues when the cartridge runs out of staples unless you have configured the device to stop when staples run out. Replace the staple cartridge. For information about replacing the staple cartridge see Order parts, accessories, and supplies. The Digital Sending Service at does not service this MFP. Contact administrator. The MFP cannot communicate with the specified IP address. Verify the IP address. Contact the network administrator. The Digital Sending Service must be upgraded to support this version of the MFP firmware. Contact administrator. The Digital Sending Service is not supported by the version of the firmware that is currently installed for the MFP. Check the firmware version. Contact the network administrator. The folder you have entered is not a valid folder. The folder name was entered incorrectly, or Re-enter the folder name correctly, or add the folder does not exist. the folder. TOO MANY PAGES IN JOB TO STAPLE The maximum number of sheets the stapler For print jobs that have more than 30 can staple is 30. pages, staple them manually. Unable to connect To temporarily hide this message in order to fax or send to e-mail, touch Hide. If this 186 Chapter 11 Problem solving ENWW

Section	Page
Device basics	13
Device comparison	14
Features comparison	15
Walkaround	18
Accessories and supplies	19
Interface ports	20
Locking and unlocking optional accessories	21
Device software	22
Supported operating systems	22
Supported printer drivers	22
Select the correct printer driver	23
Universal printer drivers	23
Driver Autoconfiguration	23
Update Now	24
HP Driver Preconfiguration	24
Priority for print settings	24
Open the printer drivers	25
Software for Macintosh computers	26
Remove software from Macintosh operating systems	26
Utilities	27
HP Web Jetadmin	27
Embedded Web server	27
HP Easy Printer Care software	28
Supported operating systems	28
Supported browsers	28
Other components and utilities	28
Control Panel	29
Use the control panel	30
Control-panel layout	30
Home screen	31
Buttons on the touchscreen	32
Control-panel help system	32
Navigate the Administration menu	33
Information menu	34
Default Job Options menu	35
Default Options for Originals	35
Default Copy Options	36
Default Fax Options	37
Default E-mail Options	38
Default Send to Folder Options	39
Default Print Options	40
Time/Scheduling menu	41
Management menu	43
Initial Setup menu	44
Networking and I/O	44
Fax Setup	52
E-mail Setup	55
Send Setup menu	55
Device Behavior menu	56
Print Quality menu	61
Troubleshooting menu	63
Resets menu	67
Service menu	68
Input/output (I/O)	69
USB configuration	70
Network configuration	71
Configure TCP/IPv4 parameters	71
Set an IP address	71
Set the subnet mask	72
Set the default gateway	72
Configure TCP/IPv6 parameters	73
Disable network protocols (optional)	73
Disable IPX/SPX	73
Disable AppleTalk	74
Disable DLC/LLC	74
HP Jetdirect EIO print servers	74
Media and trays	75
General media specifications	76
General guidelines for media	77
Paper to avoid	77
Paper that can damage the device	77
General media specifications	78
Media considerations	79
Envelopes	79
Envelopes with double side seams	79
Envelopes with adhesive strips or flaps	80
Envelope margins	80
Envelope storage	80
Labels	80
Label construction	81
Transparencies	81
Card stock and heavy media	81
Card stock construction	81
Card stock guidelines	82
Letterhead and preprinted forms	82
Select the correct fuser mode	82
Select print media	84
Printing and paper-storage environment	89
Load media	90
Load the flatbed scanner	90
Load the ADF	90
Load tray1	90
Load trays 2, 3, 4 and 5	91
Load special media	95
Load envelopes	95
Load labels	96
Load transparencies	97
Load letterhead, prepunched, or preprinted paper	97
Load paper that has a special finish	98
Load small sizes, custom sizes, or heavy paper	99
Weight and sizes	99
Guidelines for heavy paper	99
Guidelines for custom-size paper	100
Additional guidelines for small or narrow paper	100
Control print jobs	101
Select output bins	102
Select an output location	102
3‑bin mailbox output bins	102
Selecting face-up or face-down output for copy jobs	102
Use device features	105
Use the stapler	106
Configure the printer driver to recognize the optional stapler	106
Staple media	106
Load staples	108
Use job storage features	110
Gain access to the job storage features	110
Use the proof and hold feature	110
Create a proof and hold job	110
Print the remaining copies of a proof and hold job	111
Delete a proof and hold job	111
Use the private job feature	112
Create a private job	112
Print a private job	112
Delete a private job	112
Use the QuickCopy feature	113
Create a QuickCopy job	113
Print additional copies of a QuickCopy job	113
Delete a QuickCopy job	113
Use the stored job feature	114
Create a stored copy job	114
Create a stored print job	114
Print a stored job	114
Delete a stored job	115
Print	117
Use features in the Windows printer driver	118
Create and use quick sets	118
Use watermarks	119
Resize documents	119
Set a custom paper size from the printer driver	120
Use different paper and printing covers	120
Print a blank first page	120
Print multiple pages on one sheet of paper	121
Print on both sides of the paper	122
Use automatic duplex printing	122
Print on both sides manually	123
Layout options for printing on both sides	123
Use the Services tab	124
Use features in the Macintosh printer driver	125
Create and use presets	125
Print a cover page	126
Print multiple pages on one sheet of paper	126
Print on both sides of the paper	127
Cancel a print job	128
Stop the current print job from the control panel	128
Stop the current print job from the software program	128
Copy	129
Use the Copy screen	130
Set the default copy options	131
Basic copy instructions	132
Copy from the scanner glass	132
Copy from the document feeder	132
Adjust the copy settings	133
Copy two-sided documents	134
Copying two-sided documents manually	134
Copy two-sided documents automatically (duplex models only)	134
Copy mixed-size originals	136
Change the copy-collation setting	137
Copy photos and books	138
Combine copy jobs by using Job Build	139
Cancel a copy job	140
Scan and send to e-mail	141
Configure e-mail settings	142
Supported protocols	142
Configure e-mail server settings	142
Find gateways	143
Find the SMTP gateway from the device control panel	143
Find the SMTP gateway from an e-mail program	143
Use the Send E-mail screen	144
Perform basic e-mail functions	145
Load documents	145
Send documents	145
Send a document	145
Use the auto-complete function	146
Use the address book	147
Create a recipient list	147
Use the local address book	147
Add e-mail addresses to the local address book	148
Delete e-mail addresses from the local address book	148
Change e‑mail settings for the current job	149
Scan to a folder	150
Scan to a workflow destination	151
Fax	153
Analog fax	154
Install the fax accessory	154
Connect the fax accessory to a phone line	156
Configure and use the fax features	157
Digital fax	158
Manage and maintain the device	159
Use information pages	160
Configure e-mail alerts	162
HPEasy Printer Care software	163
Open the HP Easy Printer Care software	163
HP Easy Printer Care software sections	163
Use the embedded Web server	165
Open the embedded Web server by using a network connection	165
Embedded Web server sections	165
Use HP Web Jetadmin software	168
Use the HPPrinter Utility for Macintosh	169
Open the HP Printer Utility	169
HP Printer Utility features	169
Manage supplies	171
Supplies life expectancy	171
Change the print cartridge	171
Manage the print cartridge	171
Print-cartridge storage	171
Use genuine HP print cartridges	171
HP policy on non-HP print cartridges	172
Print-cartridge authentication	172
HP fraud hotline and Web site	172
Clean the device	173
Clean the exterior	173
Clean the scanner glass	173
Clean the scanner lid backing	174
Clean the paper path	174
Clean the document feeder	174
Clean the document feeder delivery system	175
Clean the document feeder-rollers	176
Calibrate the scanner	178
Problem solving	179
Problem-solving checklist	180
Factors that affect performance	180
Problem-solving flowchart	181
Solve general device problems	186
Control-panel message types	189
Control-panel messages	190
Common causes of jams	200
Clear jams	201
Clear jams from the top-cover and print-cartridge areas	202
Clear jams from the optional envelope-feeder area	204
Clear jams from the tray1 area	206
Clear jams from the tray2, 3, 4, or 5 areas	207
Clear jams from the optional duplexer	209
Clear jams from the output areas	210
Clear jams from the fuser	211
Clear jams from the document feeder	214
Solve repeated jams	215
Paper-path test	216
Clear staple jams	217
Solve print-quality problems	219
Print-quality problems associated with media	219
Print-quality problems associated with the environment	219
Print-quality problems associated with jams	219
Image defect examples	219
Light print (partial page)	221
Light print (entire page)	221
Specks	221
Dropouts	222
Lines	222
Gray background	223
Toner smear	223
Loose toner	224
Repeating defects	224
Repeating image	224
Misformed characters	225
Page skew	225
Curl or wave	226
Wrinkles or creases	226
Vertical white lines	227
Tire tracks	227
White spots on black	227
Scattered lines	228
Blurred print	228
Random image repetition	229
Solve network printing problems	230
Solve copy problems	231
Prevent copy problems	231
Image problems	231
Media-handling problems	232
Performance problems	234
Solve fax problems	235
Solve sending problems	235
Solve receiving problems	236
Solve e-mail problems	238
Validate the SMTP gateway address	238
Validate the LDAP gateway address	238
Solve common Windows problems	239
Solve common Macintosh problems	240
Solve Linux problems	243
Solve PostScript problems	244
General problems	244
Accessories and consumables	245
Order parts, accessories, and supplies	246
Order directly from HP	246
Order through service or support providers	246
Order directly through the embedded Web server (for printers that are connected to a network)	246
Order directly through the HP Easy Printer Care software	246
Part numbers	247
Accessories	247
Print cartridges	247
Maintenance kits	248
Memory	248
Cables and interfaces	248
Print media	248
Service and support	251
Hewlett-Packard limited warranty statement	251
Print cartridge limited warranty statement	252
Customer Self Repair Warranty Service	253
HP Customer Care	254
Online Services	254
Telephone support	254
Software utilities, drivers, and electronic information	254
HP direct ordering for accessories or supplies	254
HP service information	254
HP service agreements	254
HP Easy Printer Care software	255
HP support and information for Macintosh computers	255
HP maintenance agreements	256
On-site service agreements	256
Next-day on-site service	256
Weekly (volume) on-site service	256
Repacking the device	256
Extended warranty	257
Specifications	259
Physical specifications	260
Electrical specifications	260
Acoustic specifications	261
Operating environment	262
Regulatory information	263
FCC regulations	264
Environmental product stewardship program	265
Protecting the environment	265
Ozone production	265
Power consumption	265
Toner consumption	265
Paper use	265
Plastics	265
HP LaserJet print supplies	266
HP print supplies returns and recycling program information	266
Paper	266
Material restrictions	267
Disposal of waste equipment by users in private households in the European Union	267
Material Safety Data Sheet (MSDS)	268
For more information	268
Telecom statement	269
Declaration of conformity	270
Safety statements	271
Laser safety	271
Canadian DOC regulations	271
VCCI statement (Japan)	271
Power cord statement (Japan)	271
EMI statement (Korea)	271
Laser statement for Finland	271
Working with memory and print server cards	273
Overview	274
Adding printer memory	275
Installing printer memory	275
Checking DIMM installation	278
Save resources (permanent resources)	279
Enabling memory for Windows	280
Using HPJetdirect print server cards	281
Install an HP Jetdirect print server card	281
Remove an HP Jetdirect print server card	282

Match case Limit results 1 per page

Control panel message

Description

Recommended action

PIN is incorrect. Please enter a 4-digit

number.

The PIN format is incorrect.

Type the 4-digit PIN.

PIN is incorrect. Please re-enter PIN.

The PIN was typed incorrectly.

Retype the PIN.

Please turn device off and install hard

disk.

The requested job requires a hard disk, but

the MFP does not have a hard disk installed.

Turn the MFP off and install a hard disk.

See

Order

parts,

accessories,

and

supplies

Reattach output bin

The standard output bin was detached

when the MFP was turned on, or the cable

on the stapler/stacker or the 3-bin mailbox

is not connected to the MFP.

Turn the MFP off. If you are using the

stapler/stacker or the 3-bin mailbox, make

sure that the cable is connected to the

MFP. Reattach the output bin, and then

turn the MFP on. Observe the LED on the

output device. If it is flashing or amber, see

Solve

general

device

problems

Reinsert duplexer

The duplexer has been removed and must

be reinstalled.

Reinsert the duplexer in the MFP.

Reinstall output device

The output device has been removed or is

not attached.

Make sure the output bin, 3-bin mailbox, or

stapler/stacker is correctly installed on the

MFP.

Replace cartridge

The print cartridge has reached the end of

its life. Printing cannot continue.

Replace the print cartridge. To order a new

print cartridge, see

Order

parts,

accessories,

and

supplies

Replace staple cartridge

The stapler is out of staples.

Replace the staple cartridge. For

information about replacing the staple

cartridge see

Order

parts,

accessories,

and

supplies

SANITIZING DISK <X>% COMPLETE Do

not power off

The hard disk is being cleaned.

Contact the network administrator.

SCAN FAILURE Press 'Start' to rescan

The scan was unsuccessful and the

document needs to be rescanned.

If necessary, reposition the document to

rescan it, and then press

Start

SMTP Gateway

The SMTP gateway has exceeded a time

out value.

Verify the e-mail server address. See

Solve

e-mail

problems

. Contact the network

administrator.

STAPLER LOW ON STAPLES

Fewer than 20 staples remain in the staple

cartridge. Printing continues when the

cartridge runs out of staples unless you

have configured the device to stop when

staples run out.

Replace the staple cartridge. For

information about replacing the staple

cartridge see

Order

parts,

accessories,

and

supplies

The Digital Sending Service at <IP

Address> does not service this MFP.

Contact administrator.

The MFP cannot communicate with the

specified IP address.

Verify the IP address. Contact the network

administrator.

The Digital Sending Service must be

upgraded to support this version of the

MFP firmware. Contact administrator.

The Digital Sending Service is not

supported by the version of the firmware

that is currently installed for the MFP.

Check the firmware version. Contact the

network administrator.

The folder you have entered is not a

valid folder.

The folder name was entered incorrectly, or

the folder does not exist.

Re-enter the folder name correctly, or add

the folder.

TOO MANY PAGES IN JOB TO STAPLE

The maximum number of sheets the stapler

can staple is 30.

For print jobs that have more than 30

pages, staple them manually.

Unable to connect

To temporarily hide this message in order

to fax or send to e-mail, touch

Hide

. If this

Table 11-1

Control-panel messages (continued)

186

Chapter 11

Problem solving

ENWW