HP Notebook 100 Armada 100S Series Reference Guide - Page 32

System Expansion, External Connections

Page 32 highlights

Chapter 4 System Expansion This chapter introduces the optional devices for your notebook provide instructions on how to install some of the devices. External Connections Connectors on the rear and side panels of the notebook allow you to connect external devices. See Figure 1-1 and Figure 1-3 for connector locations and the descriptions that follow. This section provides notes on using some of the connectors. Connecting an External Monitor If you want the benefits of a larger color display screen, you can connect an external VGA-compatible monitor to your notebook. Follow these steps to connect a monitor to your notebook: 1. Make sure that your monitor is configured for analog operation and that the voltage setting corresponds to that of the electrical outlet. Consult the monitor's manual for instructions. 2. Make sure the notebook is not turned on. 3. On the rear of the notebook, plug the monitor's D-type signal connector to the notebook's VGA port, marked as (Figure 1-3 #6). 4. Ensure power is properly connected to the external monitor. 5. To use the monitor, turn on the monitor before turning on the notebook. 6. The monitor should respond by default. If not, you can switch the display to the monitor by pressing [Fn]+[F5]. Supplied with your notebook are several video utilities and drivers that offer extended video modes. See Chapter 6 for additional information. System Expansion 4-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65

System Expansion
4-1
Chapter 4
System Expansion
This chapter introduces the optional devices for your notebook provide instructions
on how to install some of the devices.
External Connections
Connectors on the rear and side panels of the notebook allow you to connect
external devices. See Figure 1-1 and Figure 1-3 for connector locations and the
descriptions that follow. This section provides notes on using some of the
connectors.
Connecting an External Monitor
If you want the benefits of a larger color display screen, you can connect an
external VGA-compatible monitor to your notebook. Follow these steps to connect
a monitor to your notebook:
1.
Make sure that your monitor is configured for analog operation and that the
voltage setting corresponds to that of the electrical outlet. Consult the
monitor’s manual for instructions.
2.
Make sure the notebook is not turned on.
3.
On the rear of the notebook, plug the monitor’s D-type signal connector to the
notebook’s VGA port, marked as
(Figure 1-3 #6).
4.
Ensure power is properly connected to the external monitor.
5.
To use the monitor, turn on the monitor before turning on the notebook.
6.
The monitor should respond by default. If not, you can switch the display to
the monitor by pressing [Fn]+[F5].
Supplied with your notebook are several video utilities and drivers that offer
extended video modes. See Chapter 6 for additional information.