HP ProDesk 400 G1 Micro Maintenance and Service Guide ProDesk 400 G1 Microtowe - Page 77

Installing a 3.5-inch device (model 400), device 2 to secure it in place.

Get HP ProDesk 400 G1 Micro PDF manuals and user guides View all HP ProDesk 400 G1 Micro manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Installing a 3.5-inch device (model 400) 1. Prepare the computer for disassembly (Preparation for disassembly on page 42). 2. Remove the access panel (Access panel on page 43). 3. Remove the front bezel (Front bezel on page 44). Remove the front bezel. If you are installing a drive in a bay covered by a bezel blank, remove the bezel blank. 4. Slide the device into the drive bay (1) and install the two 6-32 mounting screws in the side of the device (2) to secure it in place. NOTE: HP has supplied extra 6-32 mounting screws on the front of the chassis behind the bezel. Refer to Drives on page 59 for an illustration of the extra mounting screws location. When replacing a device, use the two 6-32 mounting screws that were removed from the old device to install the new one. Drives 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
Installing a 3.5-inch device (model 400)
1.
Prepare the computer for disassembly (
Preparation for disassembly
on page
42
).
2.
Remove the access panel (
Access panel
on page
43
).
3.
Remove the front bezel (
Front bezel
on page
44
). Remove the front bezel. If you are installing a
drive in a bay covered by a bezel blank, remove the bezel blank.
4.
Slide the device into the drive bay (1) and install the two 6-32 mounting screws in the side of the
device (2) to secure it in place.
NOTE:
HP has supplied extra 6-32 mounting screws on the front of the chassis behind the bezel.
Refer to
Drives
on page
59
for an illustration of the extra mounting screws location.
When replacing a device, use the two 6-32 mounting screws that were removed from the old
device to install the new one.
Drives
67