HP ProLiant DL980 DL980 G7 Maintenance & Service Guide - Page 28

Removing the server from the rack, Remove the access panel, WARNING, CAUTION

Get HP ProLiant DL980 - G7 Server PDF manuals and user guides View all HP ProLiant DL980 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

3. After performing the installation or maintenance procedure, slide the server into the rack by pressing the server rail-release latches. Removing the server from the rack WARNING: The server weighs approximately 72.6 kg-93 kg (160 lb-205 lb). To reduce the risk of injury due to the weight of the server, remove the following components before removing the server from the rack: • Processor memory module • Hard drives • Power supplies The server weighs 72.6 kg (160 lb) with these components removed and might require two people to remove the server from the rack. 1. Power down the server (on page 26). 2. Remove the following components to reduce the weight of the server: o Processor memory module o Hard drives o Power supplies 3. Disconnect the cabling, and remove the server from the rack. For more information, see the documentation that ships with the rack mounting option. 4. Place the server on a sturdy, level surface. Remove the access panel WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: For proper cooling do not operate the server without the access panel, baffles, expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize the amount of time the access panel is open. Illustrated parts catalog 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Illustrated parts catalog 28
3.
After performing the installation or maintenance procedure, slide the server into the rack by pressing
the server rail-release latches.
Removing the server from the rack
WARNING:
The server weighs approximately 72.6 kg–93 kg (160 lb–205 lb). To reduce the
risk of injury due to the weight of the server, remove the following components before
removing the server from the rack:
•
Processor memory module
•
Hard drives
•
Power supplies
The server weighs 72.6 kg (160 lb) with these components removed and might require two
people to remove the server from the rack.
1.
Power down the server (on page
26
).
2.
Remove the following components to reduce the weight of the server:
o
Processor memory module
o
Hard drives
o
Power supplies
3.
Disconnect the cabling, and remove the server from the rack. For more information, see the
documentation that ships with the rack mounting option.
4.
Place the server on a sturdy, level surface.
Remove the access panel
WARNING:
To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION:
For proper cooling do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components,
minimize the amount of time the access panel is open.