HP ProLiant DL980 DL980 G7 Maintenance & Service Guide - Page 29

Remove the processor memory drawer, latches catch.

Get HP ProLiant DL980 - G7 Server PDF manuals and user guides View all HP ProLiant DL980 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

To remove the component: 1. Power down the server if performing a non-hot-plug installation or maintenance procedure ("Power down the server" on page 26). 2. Extend the server from the rack. 3. Use the T-15 Torx screwdriver attached to the rear of the server to loosen the security screw on the hood latch. 4. Lift up on the hood latch handle, and then remove the access panel. Remove the processor memory drawer 1. Power down the server (on page 26). 2. Release the latches on the release lever. 3. Lower the handle, and then extend the processor memory drawer from the server until the release latches catch. 4. Firmly holding the processor memory drawer, press the release buttons and then remove the drawer from the server. 5. Remove the processor memory drawer cover. The procedure is the same for both the upper and lower processor memory drawer. Illustrated parts catalog 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Illustrated parts catalog 29
To remove the component:
1.
Power down the server if performing a non-hot-plug installation or maintenance procedure ("
Power
down the server
" on page
26
).
2.
Extend the server from the rack.
3.
Use the T-15 Torx screwdriver attached to the rear of the server to loosen the security screw on the
hood latch.
4.
Lift up on the hood latch handle, and then remove the access panel.
Remove the processor memory drawer
1.
Power down the server (on page
26
).
2.
Release the latches on the release lever.
3.
Lower the handle, and then extend the processor memory drawer from the server until the release
latches catch.
4.
Firmly holding the processor memory drawer, press the release buttons and then remove the drawer
from the server.
5.
Remove the processor memory drawer cover.
The procedure is the same for both the upper and lower processor memory drawer.