HP Scitex FB500 HP Scitex FB500 and FB700 Printer Series - User Guide - Page 16

General Media Settings, Print Mode Specific Settings

Get HP Scitex FB500 PDF manuals and user guides View all HP Scitex FB500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

For each media type, the Media Wizard stores the following settings (as indicated, some settings apply to either roll-fed or sheet-fed media only): ● General Media Settings ◦ Vacuum Fan Level - adjusts the amount of vacuum at the media drive belt. Observe the media as the fan speed changes. If the media is lifting off the belt, increase the fan speed. If the media advance seems impeded by the vacuum, decrease the fan speed. ◦ Feed Method - Rollfed (with optional supply and takeup system installed) or Cut Sheet. ◦ Visible to Printer - if Yes, the media sensor and image sensor will be used. If No, the media sensor and image sensor will not be used (with clear films, for example). ◦ Use Rollers - sets whether the Input and Output media rollers are used (yes) or not used (no) with the Flat Media setting (see Load rigid media on page 12). When set to Yes, the rollers will move up or down as needed to be just above the surface of the media. When set to No, the rollers will move to their highest point and remain there. ◦ Weight - sets the media belt drive motor and media advance amount to handle Light (up to 22 kg (50 lb)) or Heavy (22-113 kg (50-250 lb)) media. CAUTION: The input and output tables are rated at a maximum load of 68.0 kg (150 lb). Do not exceed this maximum load. ● Print Mode Specific Settings - for custom media types, this screen enables you to adjust the settings for each print mode and color set combination. See Available print modes on page 21 for a detailed description of print modes and color sets. ◦ Print Mode - select the print mode whose settings you want to change. ◦ Color Set - select the color set whose settings you want to change. ◦ Change Print Mode Specific Settings - press this button to change the UV Lamps settings and Printing Delay for the print mode and color set you selected. A higher lamp setting increases ink curing power, important at high speeds and for older lamps that are losing their intensity; a lower setting for newer lamps extends their life. Closing the shutter on the trailing lamp blocks the UV light from the lamp, which allows the drop of jetted ink to spread out more before it is cured, resulting in a glossier look to the print. The color profile used must take this into account for accurate color matching. A longer printing delay helps dissipate heat from heat-sensitive substrates, while a shorter delay speeds printing throughput. 10 Chapter 2 Configure and load media ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
For each media type, the Media Wizard stores the following settings (as indicated, some settings
apply to either roll-fed or sheet-fed media only):
●
General Media Settings
◦
Vacuum Fan Level — adjusts the amount of vacuum at the media drive belt. Observe the
media as the fan speed changes. If the media is lifting off the belt, increase the fan speed.
If the media advance seems impeded by the vacuum, decrease the fan speed.
◦
Feed Method — Rollfed (with optional supply and takeup system installed) or Cut Sheet.
◦
Visible to Printer — if Yes, the media sensor and image sensor will be used. If No, the
media sensor and image sensor will not be used (with clear films, for example).
◦
Use Rollers — sets whether the Input and Output media rollers are used (yes) or not used
(no) with the Flat Media setting (see
Load rigid media
on page
12
). When set to Yes, the
rollers will move up or down as needed to be just above the surface of the media. When set
to No, the rollers will move to their highest point and remain there.
◦
Weight — sets the media belt drive motor and media advance amount to handle Light (up
to 22 kg (50 lb)) or Heavy (22-113 kg (50-250 lb)) media.
CAUTION:
The input and output tables are rated at a maximum load of 68.0 kg (150 lb).
Do not exceed this maximum load.
●
Print Mode Specific Settings
— for custom media types, this screen enables you to adjust the
settings for each print mode and color set combination. See
Available print modes
on page
21
for a detailed description of print modes and color sets.
◦
Print Mode — select the print mode whose settings you want to change.
◦
Color Set — select the color set whose settings you want to change.
◦
Change Print Mode Specific Settings — press this button to change the UV Lamps settings
and Printing Delay for the print mode and color set you selected. A higher lamp setting
increases ink curing power, important at high speeds and for older lamps that are losing
their intensity; a lower setting for newer lamps extends their life.
Closing the shutter on the trailing lamp blocks the UV light from the lamp, which allows the
drop of jetted ink to spread out more before it is cured, resulting in a glossier look to the
print. The color profile used must take this into account for accurate color matching.
A longer printing delay helps dissipate heat from heat-sensitive substrates, while a shorter
delay speeds printing throughput.
10
Chapter 2
Configure and load media
ENWW