HP StoreOnce D2D4324 HP StoreOnce Backup System CLI Reference Guide (BB877-909 - Page 125

system enable failover, If failover is already enabled, the following is displayed

Get HP StoreOnce D2D4324 PDF manuals and user guides View all HP StoreOnce D2D4324 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

system enable failover NOTE: This command applies to multi-node products only. Description of Command Function Enables the failover feature on the StoreOnce appliance. It is a direct map to the command sequence hardware enable failover (see "hardware enable failover" (page 35)). For the initial release, this command will only enable failover for the entire appliance. In following releases, the command will be updated to enable failover for give service sets. Command Syntax system enable failover Command Authority Administrator Command Object Requirements Not applicable - objects exist within this command. Command Parameter Requirements Not applicable - no parameters exist within this command. Requirements for Command Execution • The command entry must conform to the command syntax. • Failover must already be disabled. Successful Command Output Upon successful completion of the command, the following is displayed: failover enabled Command Operation during Abnormal Conditions • If the command does not conform to the required syntax, the following is displayed: Command Failed - the command does not conform to the required syntax, SYNTAX, where SYNTAX is the command syntax as described under Command Syntax in this section. • If failover is already enabled, the following is displayed: Command Failed - failover is already enabled Example # system enable failover failover enabled system enable failover 125

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
system enable failover
NOTE:
This command applies to multi-node products only.
Description of Command Function
Enables the failover feature on the StoreOnce appliance. It is a direct map to the command sequence
hardware enable failover
(see
“hardware enable failover” (page 35)
). For the initial release,
this command will only enable failover for the entire appliance. In following releases, the command
will be updated to enable failover for give service sets.
Command Syntax
system enable failover
Command Authority
Administrator
Command Object Requirements
Not applicable – objects exist within this command.
Command Parameter Requirements
Not applicable – no parameters exist within this command.
Requirements for Command Execution
•
The command entry must conform to the command syntax.
•
Failover must already be disabled.
Successful Command Output
Upon successful completion of the command, the following is displayed:
failover enabled
Command Operation during Abnormal Conditions
•
If the command does not conform to the required syntax, the following is displayed:
Command Failed - the command does not conform to the required syntax,
SYNTAX
, where SYNTAX is the command syntax as described under Command Syntax in this
section.
•
If failover is already enabled, the following is displayed:
Command Failed - failover is already enabled
Example
# system enable failover
failover enabled
system enable failover
125