HP StoreOnce D2D4324 HP StoreOnce Backup System CLI Reference Guide (BB877-909 - Page 90

net show config, object is not included in the command sequence

Get HP StoreOnce D2D4324 PDF manuals and user guides View all HP StoreOnce D2D4324 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

net show config NOTE: This command applies to single-node products only. Description of Command Function Shows the network configuration. Command Syntax net show config [all] Command Authority Operator and Administrator Command Object Requirements netlabel- This object defines the name of the specific network configuration to be shown. If the object is not included in the command sequence, the parameter "all" must be included in the command sequence. Command Parameter Requirements all- This parameter is optional. If included in the command sequence, all templates in the existing network configuration are described. If this command is not included, a network template object must be included in the command sequence. Requirements for Command Execution The command entry must conform to the command syntax. Successful Command Output Upon successful completion of the command, information on the external network configuration is displayed. Command Operation during Abnormal Conditions If the command does not conform to the required syntax, the following is displayed: Command Failed - the command does not conform to the required syntax, SYNTAX, where SYNTAX is the command syntax as described under Command Syntax in this section. Example # net show config current Network Name: current Network Description: default Write Protected: no DNS Servers Number of Networks:1 Network: subnet_one IP Address: dhcp Net Mask: dhcp Domain Name: dhcp Gateway: dhcp Bonding Mode: 6 (High Availability) Default Network: yes Interfaces:eth0 Command Successful # net show config all Network Name: Factory_Default_Configuration Network Description: default 90 Alphabetical List of Commands and Details

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
net show config
NOTE:
This command applies to single-node products only.
Description of Command Function
Shows the network configuration.
Command Syntax
net show config <netlabel> [all]
Command Authority
Operator and Administrator
Command Object Requirements
netlabel
— This object defines the name of the specific network configuration to be shown. If the
object is not included in the command sequence, the parameter “all” must be included in the
command sequence.
Command Parameter Requirements
all
— This parameter is optional. If included in the command sequence, all templates in the existing
network configuration are described. If this command is not included, a network template object
must be included in the command sequence.
Requirements for Command Execution
The command entry must conform to the command syntax.
Successful Command Output
Upon successful completion of the command, information on the external network configuration is
displayed.
Command Operation during Abnormal Conditions
If the command does not conform to the required syntax, the following is displayed:
Command Failed - the command does not conform to the required syntax,
SYNTAX
, where SYNTAX is the command syntax as described under Command Syntax in this
section.
Example
# net show config current
----------------------
Network Name: current
Network Description: default
Write Protected: no
DNS Servers:
----------------------
Number of Networks:1
----------------------
Network: subnet_one
----------------------
IP Address: dhcp
Net Mask: dhcp
Domain Name: dhcp
Gateway: dhcp
Bonding Mode: 6 (High Availability)
Default Network: yes
Interfaces:eth0
Command Successful
# net show config all
----------------------
Network Name: Factory_Default_Configuration
Network Description: default
90
Alphabetical List of Commands and Details