HP StoreOnce D2D4324 HP StoreOnce Backup System CLI Reference Guide (BB877-909 - Page 31

hardware delete storage, response for command execution to continue. Upon successful completion

Get HP StoreOnce D2D4324 PDF manuals and user guides View all HP StoreOnce D2D4324 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

hardware delete storage NOTE: This command applies to single-node products only. Description of Command Function Deletes storage segments associated with the StoreOnce system "backend" file system. This command does not apply to the storage on which each nodes operating system is located. Command Syntax Hardware delete storage {ALL|dev-id} Command Authority Administrator Command Object Requirements Not applicable - no objects exist within this command. Command Parameter Requirements • ALL - When this global parameter is defined in the command sequence, all couplet file systems, logical segments, logical volumes, and physical volume are removed. The system is left in a state in which no storage is configured. The command requires this parameter or a dev-id value. • dev-id - This parameter defines a specific volume to be deleted. A specific volume is defined as a storage component with a specific SCSI LUN. The device ID for the storage component to be deleted can be determined using the hardware show status command. The command requires this parameter or the global ALL. Requirements for Command Execution • The command entry must conform to the command syntax. • All parameter values must be valid; see the parameter descriptions for details. Successful Command Output Prior to executing the command the following message is displayed: Warning - Data may be destroyed. Are you sure you want to delete storage? y / n You must enter a y response for command execution to continue. Upon successful completion of the command, the following is displayed: Command Successful Command Operation during Abnormal Conditions • If any of the command execution requirements fail, command execution terminates. The beacon status is unchanged and one of these error messages is displayed: ◦ Command Failed - the command does not conform to the required syntax, SYNTAX, where SYNTAX is the command syntax as described under Command Syntax in this section. ◦ Command Failed - The global parameter ALL or a device ID must be defined ◦ Command Failed - The device ID is not a storage volume ◦ Command Failed - The device does not exist hardware delete storage 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
hardware delete storage
NOTE:
This command applies to single-node products only.
Description of Command Function
Deletes storage segments associated with the StoreOnce system “backend” file system. This
command does not apply to the storage on which each nodes operating system is located.
Command Syntax
Hardware delete storage {ALL|dev-id}
Command Authority
Administrator
Command Object Requirements
Not applicable – no objects exist within this command.
Command Parameter Requirements
•
ALL
– When this global parameter is defined in the command sequence, all couplet file systems,
logical segments, logical volumes, and physical volume are removed. The system is left in a
state in which no storage is configured. The command requires this parameter or a dev-id
value.
•
dev-id
– This parameter defines a specific volume to be deleted. A specific volume is defined
as a storage component with a specific SCSI LUN. The device ID for the storage component
to be deleted can be determined using the
hardware show status
command. The
command requires this parameter or the global ALL.
Requirements for Command Execution
•
The command entry must conform to the command syntax.
•
All parameter values must be valid; see the parameter descriptions for details.
Successful Command Output
Prior to executing the command the following message is displayed:
Warning
–
Data may be destroyed. Are you sure you want to delete storage?
y / n
You must enter a
y
response for command execution to continue. Upon successful completion of
the command, the following is displayed:
Command Successful
Command Operation during Abnormal Conditions
•
If any of the command execution requirements fail, command execution terminates. The beacon
status is unchanged and one of these error messages is displayed:
◦
Command Failed - the command does not conform to the required
syntax, SYNTAX
, where SYNTAX is the command syntax as described under Command
Syntax in this section.
◦
Command Failed
–
The global parameter ALL or a device ID must be
defined
◦
Command Failed
–
The device ID is not a storage volume
◦
Command Failed
–
The device does not exist
hardware delete storage
31