Home » HP Manuals » Storage Devices » HP StoreOnce D2D4324 » Manual Viewer

HP StoreOnce D2D4324 HP StoreOnce Backup System CLI Reference Guide (BB877-909 - Page 50

hardware show status, All parameter values must be valid; see the parameter descriptions for details.

View all HP StoreOnce D2D4324 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

hardware show status Description of Command Function Provides status on all the hardware components of the StoreOnce system. Command Syntax hardware show status [detail] [dev-id] Command Authority Operator and Administrator Command Object Requirements Not applicable - no objects exist within this command. Command Parameter Requirements • detail - This optional parameter provides a detailed output for the hardware components selected. If not defined, only the device ID and its status are provided. • dev-id - This optional parameter selects a particular device and its immediate children to have their statuses shown. If not defined, the top level status and device IDs of couplets (with their nodes and storage arrays) and internal network switches are shown. The device ID of any component can be found using the hardware show status command and then using that device ID with the same command to view the device IDs of its subcomponents. Requirements for Command Execution • The command entry must conform to the command syntax. • All parameter values must be valid; see the parameter descriptions for details. Successful Command Output Upon successful completion of the command, the status of the selected devices is shown. NOTE: If CLI paging is enabled, the output of this command is displayed with paging. Command Operation during Abnormal Conditions If any of the command execution requirements fail, command execution terminates. The hardware status is not displayed and one of these error messages is displayed: • Command Failed - the command does not conform to the required syntax, SYNTAX, where SYNTAX is the command syntax as described under Command Syntax in this section. • Command Failed - Component for the device ID does not exist in system Examples > hardware show status dev-id StatusText Couplet_1 down - msa1 warn - msa2 warn - hp85647867b2-2 up - hp85647867b2-1 up switch1 up switch2 up Command Successful > hardware show status msa1 dev-id msa1 - controller-1-1 StatusText ---------warn up 50 Alphabetical List of Commands and Details

Section	Page
	1
Contents	3
1 Using the CLI	6
Introduction	6
Accessing the CLI	6
Command Entry	7
Viewing Help	7
Transferring Files	7
Scripting	7
2 Command Instruction Syntax	8
Global Defaults	9
3 Categorical List of Commands	10
4 Alphabetical List of Commands and Details	13
accounts add	13
accounts del	15
accounts modify	16
accounts show	18
alerts show	20
config delete	21
config restore devices	22
config restore keystore	24
config save devices	25
config save keystore	26
config show list	27
exit	28
hardware add storage	29
hardware beacon	30
hardware delete storage	31
hardware disable failover	33
hardware discover storage	34
hardware enable failover	35
hardware failback	36
hardware failover	37
hardware poweroff	38
hardware powerup	40
hardware prepare storage	41
hardware reboot	42
hardware set ports	43
hardware show firmware	44
hardware show net status	46
hardware show node status	48
hardware show problems	49
hardware show status	50
hardware show storage status	53
hardware update firmware	54
help	55
hpresetpassword	57
license add	58
license load	59
license show	60
logs show events	61
logs show update	63
nas create share	65
nas delete share	67
nas modify share	68
nas show share	69
net activate config	70
net add subnet	71
net copy config	73
net create config	74
net delete config	76
net delete subnet	77
net modify config	78
net modify subnet	80
net ping	82
net set config	83
net set wizard	85
net show config	88
net show config	90
net show config list	92
net show ports	93
net show status	94
net validate config	95
serviceset show status	96
serviceset start	97
serviceset stop	98
snmp add trapsink	99
snmp add user	102
snmp del trapsink	104
snmp del user	105
snmp disable	106
snmp enable	107
snmp modify trapsink	108
snmp modify user	110
snmp reset ro-community	112
snmp set contact	113
snmp set location	114
snmp set ro-community	115
snmp show config	116
snmp show user	118
support create ticket	119
support del ticket	120
support show ticket	121
system clear packages	122
system clear repository	123
system disable failover	124
system enable failover	125
system load packages	126
system reboot	127
system set clioutput	128
system set config	129
system set description	136
system set pagecontrol	137
system show config	138
system show packages	139
system show performance	140
system show repository	142
system show status	143
system shutdown	145
system update packages	146
time add ntpserver	147
time del ntpserver	149
time reset timezone	150
time set timezone	151
time set UTC	153
time show config	154
vtl create cartridge	155
vtl create library	157
vtl delete cartridge	162
vtl delete library	164
vtl modify cartridge	166
vtl modify drive	168
vtl modify library	170
vtl move cartridge	174
vtl show capacity	176
vtl show cartridges	178
vtl show drive info	180
vtl show drive list	182
vtl show library info	184
vtl show library iscsi authentication	187
vtl show library list	188
vtl show ports	189
5 Support and other resources	191
Contacting HP	191
Related information	191
Websites	191
Typographic conventions	191
Documentation feedback	192
Glossary	193

Match case Limit results 1 per page

hardware show status

Description of Command Function

Provides status on all the hardware components of the StoreOnce system.

Command Syntax

hardware show status [detail] [dev-id]

Command Authority

Operator and Administrator

Command Object Requirements

Not applicable – no objects exist within this command.

Command Parameter Requirements

•

detail

– This optional parameter provides a detailed output for the hardware components

selected. If not defined, only the device ID and its status are provided.

•

dev-id

– This optional parameter selects a particular device and its immediate children to have

their statuses shown. If not defined, the top level status and device IDs of couplets (with their

nodes and storage arrays) and internal network switches are shown. The device ID of any

component can be found using the

hardware show status

command and then using that

device ID with the same command to view the device IDs of its subcomponents.

Requirements for Command Execution

•

The command entry must conform to the command syntax.

•

All parameter values must be valid; see the parameter descriptions for details.

Successful Command Output

Upon successful completion of the command, the status of the selected devices is shown.

NOTE:

If CLI paging is enabled, the output of this command is displayed with paging.

Command Operation during Abnormal Conditions

If any of the command execution requirements fail, command execution terminates. The hardware

status is not displayed and one of these error messages is displayed:

•

Command Failed - the command does not conform to the required syntax,

SYNTAX

, where SYNTAX is the command syntax as described under Command Syntax in this

section.

•

Command Failed

–

Component for the device ID does not exist in system

Examples

> hardware show status

dev-id

StatusText

-----------------

----------

Couplet_1

down

- msa1

warn

- msa2

warn

- hp85647867b2-2

- hp85647867b2-1

switch1

switch2

Command Successful

> hardware show status msa1

dev-id

StatusText

-----------------

----------

msa1

warn

- controller-1-1

Alphabetical List of Commands and Details