HP StoreOnce D2D4324 HP StoreOnce Backup System CLI Reference Guide (BB877-909 - Page 130

Management/Data/Replication on 4 1Gb ports bonded - Template 2

Get HP StoreOnce D2D4324 PDF manuals and user guides View all HP StoreOnce D2D4324 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 130 highlights

The following configuration steps will be performed: -> Configure Network Configure Time Configure Licenses Verify Hardware health Configure Failover Finish Configuration and reboot Finish Configuration Actions: execute) Perform the current step (Default) skip) Skip to the next step back) Go back to a previous step quit) Exit the configuration immediately Configure Network [execute]? Please choose a template to apply: 1) Management on (2) 1Gb ports (bonded), Data/Replication on (2) 10Gb ports (bonded) - Template 1 2) Management/Data/Replication on (4) 1Gb ports (bonded) - Template 2 3) Management/Data/Replication on (2) 10 Gb ports (bonded) - Template 3 4) Management on (2) 1Gb ports (bonded), Data/Replication on (2) 1Gb ports (bonded) - Template 4 5) Management/Data/Replication on (2) 1Gb ports (bonded) - Template 5 quit) quit without configuring the network Please select a template (1-5) or "quit": Template #1 - Management on (2) 1Gb ports (bonded), Data/Replication on (2) 10Gb ports (bonded) Do you want to configure a 1GbE management and 10GbE data network? [Y/(N)]: Enter Virtual Management Console IP Address (must be IPv4 X.X.X.X): Select bonding mode for 1GbE management bond enter 1 (Active/Backup), 4 (IEEE 802.3ad Dynamic Link Aggregation), or 6 (Active Load Balancing), (default = 1): Enter 1GbE management network start IP address (must be IPv4 X.X.X.X): An incorrect entry... Error: The IP Address provided should not lie between the existing range of network IP addresses. Please enter the value again Enter 1GbE management network end IP address (must be IPv4 X.X.X.X): Enter 1GbE management subnet mask (must be IPv4 X.X.X.X): Select bonding mode for 10GbE data bond enter 1 (Active/Backup), 4 (IEEE 802.3ad Dynamic Link Aggregation), or 6 (Active Load Balancing), (default = 1): 1 Enter 10GbE data network start IP address (must be IPv4 X.X.X.X): Enter 10GbE data network end IP address (must be IPv4 X.X.X.X): Enter 10GbE data subnet mask (must be IPv4 X.X.X.X): Error: Incorrect number of IP address blocks entered. Please enter the values again Select bonding mode for 1GbE management bond enter 1 (Active/Backup), 4 (IEEE 802.3ad Dynamic Link Aggregation), or 6 (Active Load Balancing), (default = 1): 4 Bonding mode 4 (dynamic link aggregation) requires the ports on your network switch(es) to be configured for LACP. This change must be made immediately after applying the changes in the network configuration on this 130 Alphabetical List of Commands and Details

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
The following configuration steps will be performed:
-> Configure Network
Configure Time
Configure Licenses
Verify Hardware health
Configure Failover
Finish Configuration and reboot
Finish Configuration
Actions:
execute) Perform the current step (Default)
skip) Skip to the next step
back) Go back to a previous step
quit) Exit the configuration immediately
Configure Network [execute]?
Please choose a template to apply:
1) Management on (2) 1Gb ports (bonded), Data/Replication on (2) 10Gb ports
(bonded) - Template 1
2) Management/Data/Replication on (4) 1Gb ports (bonded) - Template 2
3) Management/Data/Replication on (2) 10 Gb ports (bonded) - Template 3
4) Management on (2) 1Gb ports (bonded), Data/Replication on (2) 1Gb ports
(bonded) - Template 4
5) Management/Data/Replication on (2) 1Gb ports (bonded) - Template 5
quit) quit without configuring the network
Please select a template (1-5) or "quit":
====================================================================
Template #1 - Management on (2) 1Gb ports (bonded), Data/Replication on (2) 10Gb ports (bonded)
Do you want to configure a 1GbE management and 10GbE data network? [Y/(N)]:
Enter Virtual Management Console IP Address
(must be IPv4
X.X.X.X):
--------------------------------------------------------------------
Select bonding mode for 1GbE management bond
enter 1 (Active/Backup),
4 (IEEE 802.3ad Dynamic Link Aggregation),
or 6 (Active Load Balancing),
(default = 1):
Enter 1GbE management network start IP address
(must be IPv4
X.X.X.X):
An incorrect entry
…
Error: The IP Address provided should not lie between the existing
range of network IP addresses. Please enter the value again
Enter 1GbE management network end IP address
(must be IPv4
X.X.X.X):
Enter 1GbE management subnet mask
(must be IPv4
X.X.X.X):
--------------------------------------------------------------------
Select bonding mode for 10GbE data bond
enter 1 (Active/Backup),
4 (IEEE 802.3ad Dynamic Link Aggregation),
or 6 (Active Load Balancing),
(default = 1): 1
Enter 10GbE data network start IP address
(must be IPv4
X.X.X.X):
Enter 10GbE data network end IP address
(must be IPv4
X.X.X.X):
Enter 10GbE data subnet mask
(must be IPv4
X.X.X.X):
Error: Incorrect number of IP address blocks entered.
Please enter the values again
--------------------------------------------------------------------
Select bonding mode for 1GbE management bond
enter 1 (Active/Backup),
4 (IEEE 802.3ad Dynamic Link Aggregation),
or 6 (Active Load Balancing),
(default = 1): 4
Bonding mode 4 (dynamic link aggregation) requires the ports on your network switch(es) to be configured for
LACP. This change must be made immediately after applying the changes in the network configuration on this
130
Alphabetical List of Commands and Details