HP StoreOnce D2D4324 HP StoreOnce Backup System CLI Reference Guide (BB877-909 - Page 129

system set config, the wizard rather than appended to the command.

Get HP StoreOnce D2D4324 PDF manuals and user guides View all HP StoreOnce D2D4324 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 129 highlights

system set config Description of Command Function Runs a step-based wizard to guide you through a complete series of system configuration steps: • Configure network • Configure time • Configure licenses • Verify hardware health • Configure failover NOTE: Configure failover only applies and is only available for configuration for multinode products. This step in the wizard is eliminated when performing a single-node product configuration. • Finish configuration and reboot • Finish configuration . Command Syntax system set config Command Authority Administrator Command Object Requirements Not applicable-no objects exist within this command Command Parameter Requirements Not applicable-no parameters exist within this command. (Any parameters are entered within the wizard rather than appended to the command.) Requirements for Command Execution The command entry must conform to the command syntax. Successful Command Output Upon successful completion of the command, system configuration set up is complete. Command Operation During Abnormal Conditions If the command does not conform to the required syntax, the following is displayed: Command Failed - the command does not conform to the required syntax, SYNTAX, where SYNTAX is the command syntax as described under Command Syntax in this section. Example NOTE: This example applies to multinode products (configure failover is not supported in single-node). > system set config Please ensure all nodes have joined the cluster prior to running this command. Found 2 nodes. Some components are in a failed state! Failed components: Couplet_1 > hpb3cce3861a-1 > node1_hba_host6 Couplet_1 > hpb3cce3861a-1 > node1_hba_host7 Continue with configuration (y/N)? failover disabled. MENU Item 1 system set config 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
system set config
Description of Command Function
Runs a step-based wizard to guide you through a complete series of system configuration steps:
•
Configure network
•
Configure time
•
Configure licenses
•
Verify hardware health
•
Configure failover
NOTE:
Configure failover only applies and is only available for configuration for multinode
products. This step in the wizard is eliminated when performing a single-node product
configuration.
•
Finish configuration and reboot
•
Finish configuration
.
Command Syntax
system set config
Command Authority
Administrator
Command Object Requirements
Not applicable—no objects exist within this command
Command Parameter Requirements
Not applicable—no parameters exist within this command. (Any parameters are entered within
the wizard rather than appended to the command.)
Requirements for Command Execution
The command entry must conform to the command syntax.
Successful Command Output
Upon successful completion of the command, system configuration set up is complete.
Command Operation During Abnormal Conditions
If the command does not conform to the required syntax, the following is displayed:
Command Failed - the command does not conform to the required syntax,
SYNTAX
, where SYNTAX is the command syntax as described under Command Syntax in this
section.
Example
NOTE:
This example applies to multinode products (configure failover is not supported in
single-node).
> system set config
Please ensure all nodes have joined the cluster prior to running this command.
Found 2 nodes. Some components are in a failed state!
Failed components:
Couplet_1 > hpb3cce3861a-1 > node1_hba_host6
Couplet_1 > hpb3cce3861a-1 > node1_hba_host7
Continue with configuration (y/N)?
failover disabled.
MENU Item 1
system set config
129