HP StoreOnce D2D4324 HP StoreOnce Backup System CLI Reference Guide (BB877-909 - Page 88

net show config, This command applies to multinode products only.

Get HP StoreOnce D2D4324 PDF manuals and user guides View all HP StoreOnce D2D4324 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

net show config NOTE: This command applies to multinode products only. Description of Command Function Shows the network configuration. Command Syntax net show config Command Authority Operator and Administrator Command Object Requirements Not applicable - no objects exist within this command. Command Parameter Requirements Not applicable - no parameters exist within this command. Requirements for Command Execution The command entry must conform to the command syntax. Successful Command Output Upon successful completion of the command, information on the external network configuration is displayed. Command Operation during Abnormal Conditions If the command does not conform to the required syntax, the following is displayed: Command Failed - the command does not conform to the required syntax, SYNTAX, where SYNTAX is the command syntax as described under Command Syntax in this section. Example # net show config External Network Configuration Template 2 Management/Data/Replication on (4) 1Gb ports (bonded) Virtual Management Console IP Address: 16.24.164.21 1GbE Network Bonding Mode 6 - Active Load Balance Bonding Node Specific Parameters Node 1: 1GbE Network Physical IP (HP Service Only): 16.24.164.22 1GbE Network Virtual Data IP: 16.24.164.23 Node 2: 1GbE Network Physical IP (HP Service Only): 16.24.164.24 1GbE Network Virtual Data IP: null Appliance Wide Parameters 1GbE subnet mask: 255.255.240.0 Data/Management network gateway: 16.24.160.1 (default) 88 Alphabetical List of Commands and Details

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
net show config
NOTE:
This command applies to multinode products only.
Description of Command Function
Shows the network configuration.
Command Syntax
net show config
Command Authority
Operator and Administrator
Command Object Requirements
Not applicable – no objects exist within this command.
Command Parameter Requirements
Not applicable – no parameters exist within this command.
Requirements for Command Execution
The command entry must conform to the command syntax.
Successful Command Output
Upon successful completion of the command, information on the external network configuration is
displayed.
Command Operation during Abnormal Conditions
If the command does not conform to the required syntax, the following is displayed:
Command Failed - the command does not conform to the required syntax,
SYNTAX
, where SYNTAX is the command syntax as described under Command Syntax in this
section.
Example
# net show config
External Network Configuration
------------------------------
Template 2
Management/Data/Replication on (4) 1Gb ports (bonded)
Virtual Management Console IP Address: 16.24.164.21
1GbE Network Bonding
Mode 6 - Active Load Balance Bonding
Node Specific Parameters
------------------------
Node 1:
1GbE Network Physical IP (HP Service Only): 16.24.164.22
1GbE Network Virtual Data IP: 16.24.164.23
Node 2:
1GbE Network Physical IP (HP Service Only): 16.24.164.24
1GbE Network Virtual Data IP: null
Appliance Wide Parameters
-------------------------
1GbE subnet mask: 255.255.240.0
Data/Management network gateway: 16.24.160.1 (default)
88
Alphabetical List of Commands and Details