HP Tc2100 hp server tc2100 installation sheet (English) - Page 34

SCSI Mass Storage Additions, Installing a Second Hard Disk Drive

Get HP Tc2100 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Chapter 4 Installing Mass Storage Devices SCSI Mass Storage Additions Table 4-2 lists the number and types of mass storage devices that may be added to the SCSI model of the HP Server. Table 4-2. SCSI Model Mass Storage Devices Interface Types FDD Max No. Devices 1 Installed Devices and Addresses Factory installed flexible disk drive (FDD) in shelf 1 IDE-2 2* • Factory installed CD-ROM drive in shelf 2 • A second IDE device (hard disk drive) could be installed, if shelf 3 is available. Internal SCSI 4*** • Factory installed SCSI HDD (shelf 6, address = ID 0 cable (Ultra-160 • Optional 2nd SCSI HDD (shelf 5, addresses = ID 1). SCSI Adapter) • Optional 3rd SCSI HDD (shelf 4, address = ID 2) • Optional SCSI Tape Backup Drive (shelf 3, address = ID 3) ** • SCSI controller (address = ID 7) External SCSI connector (Ultra-160 SCSI Adapter) 15 *** • Only used for control of external SCSI devices. This SCSI connector can control up to 15 external SCSI devices * The secondary IDE (IDE-2) cable is connected to the factory-installed CD-ROM drive and configured as master, unless 3rd hard drive installed and configured as master device. The primary IDE connector (IDE-1) is available on the SCSI model, but is not supported by Hewlett-Packard. ** A 50-to-68-pin SCSI adapter is provided with the HP backup tape drive. *** The single channel SCSI controller can support up to 15 devices on one connector at a time; however, there are only enough internal storage shelves for 3 hard drives and 1 optional tape backup device. The external connector is only used to control external SCSI devices when there are no internal SCSI devices. Installing a Second Hard Disk Drive The first hard disk drive (IDE or SCSI) is always mounted in the bottom (shelf 6) of the hard disk drive cage (also drive cage) and the second hard disk drive should be mounted just above it (shelf 5) in the drive cage. 1. If the Server is already installed and operating, power down the Server as described in Chapter 2, "Controls, Ports, and Indicators." 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Chapter 4
Installing Mass Storage Devices
28
SCSI Mass Storage Additions
Table 4-2 lists the number and types of mass storage devices that may be added to
the SCSI model of the HP Server.
Table 4-2. SCSI Model Mass Storage Devices
Interface
Types
Max No.
Devices
Installed Devices and Addresses
FDD
1
Factory installed flexible disk drive (FDD) in shelf 1
IDE-2
2*
•
Factory installed CD-ROM drive in shelf 2
•
A second IDE device (hard disk drive) could be
installed, if shelf 3 is available.
Internal SCSI
cable
(Ultra-160
SCSI Adapter)
4***
•
Factory installed SCSI HDD (shelf 6, address = ID 0
•
Optional 2nd SCSI HDD (shelf 5, addresses = ID 1).
•
Optional 3rd SCSI HDD (shelf 4, address = ID 2)
•
Optional SCSI Tape Backup Drive (shelf 3, address
= ID 3) **
•
SCSI controller (address = ID 7)
External SCSI
connector
(Ultra-160
SCSI Adapter)
15 ***
•
Only used for control of external SCSI devices.
This
SCSI connector can control up to 15 external SCSI
devices
* The secondary IDE (IDE-2) cable is connected to the factory-installed CD-ROM drive and
configured as master, unless 3
rd
hard drive installed and configured as master device. The primary
IDE connector (IDE-1) is available on the SCSI model, but is not supported by Hewlett-Packard.
** A 50-to-68-pin SCSI adapter is provided with the HP backup tape drive.
*** The single channel SCSI controller can support up to 15 devices on one connector at a time;
however, there are only enough internal storage shelves for 3 hard drives and 1 optional tape backup
device. The external connector is only used to control external SCSI devices when there are no
internal SCSI devices.
Installing a Second Hard Disk Drive
The first hard disk drive (IDE or SCSI) is always mounted in the bottom (shelf 6)
of the hard disk drive cage (also drive cage) and the second hard disk drive should
be mounted just above it (shelf 5) in the drive cage.
1. If the Server is already installed and operating, power down the Server as
described in Chapter 2, "Controls, Ports, and Indicators."