HP Tc2100 hp server tc2100 installation sheet (English) - Page 80

After Installing an Accessory, Repeat steps 1

Get HP Tc2100 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Chapter 9 Troubleshooting 9. Verify the DIMMs are installed correctly and fully seated. 10. Verify the DIMM notches are aligned to the keys in the DIMM connector. After Installing an Accessory: 1. Turn off the monitor, the Server, and any external devices. 2. Unplug all cables from the power outlet. 3. Remove the cover. 4. Check the following: o If you have installed an accessory board, verify the board is firmly seated in its slot and any switches or jumpers on the accessory board are properly set. Refer to the documentation provided with accessory board. o Check all internal cabling and connections. o If you have changed any switches on the system board, verify each one is properly set. NOTE Only two of the eight switches on configuration switch are used. 5. Replace the cover and connect all cables. 6. Turn on the monitor and Server. 7. If the Server still does not work: o Repeat steps 1, 2, and 3 of this section. o Remove all accessories, except the primary boot hard disk drive. o Replace the cover and connect all cables. o Turn on the monitor and the Server. o If the Server now works, replace the boards and accessories one at a time to determine which one is causing the problem. 8. If the Server still does not work contact your service representative to replace the Server. 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Chapter 9
Troubleshooting
74
9. Verify the DIMMs are installed correctly and fully seated.
10. Verify the DIMM notches are aligned to the keys in the DIMM connector.
After Installing an Accessory:
1. Turn off the monitor, the Server, and any external devices.
2. Unplug all cables from the power outlet.
3. Remove the cover.
4. Check the following:
o
If you have installed an accessory board, verify the board is firmly seated
in its slot and any switches or jumpers on the accessory board are properly
set.
Refer to the documentation provided with accessory board.
o
Check all internal cabling and connections.
o
If you have changed any switches on the system board, verify each one is
properly set.
NOTE
Only two of the eight switches on configuration switch are
used.
5. Replace the cover and connect all cables.
6. Turn on the monitor and Server.
7. If the Server still does not work:
o
Repeat steps 1, 2, and 3 of this section.
o
Remove all accessories, except the primary boot hard disk drive.
o
Replace the cover and connect all cables.
o
Turn on the monitor and the Server.
o
If the Server now works, replace the boards and accessories one at a time
to determine which one is causing the problem.
8. If the Server still does not work contact your service representative to replace
the Server.