HP Tc2110 hp server tc2110 operation and maintenance guide (online version 1.1 - Page 11

Powering-Up the Server, Setting the input voltage, Connecting the Power Cords

Get HP Tc2110 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Chapter 1 Controls and Indicators Setting the input voltage Remove the warning label covering the power connector, and ensure that the voltage setting is correct for your country. (The voltage is set during manufacture and should already be correct.) Figure 1-4. Input Voltage Selection Switch Connecting the Power Cords 1. Connect the power cords to the rear of the monitor and the HP Server. (The connectors are shaped to go in one way only.) 2. Connect the monitor's power cord and the HP Server's power cord to a grounded outlet. See Figure 1-4. NOTE Hewlett-Packard does not support power supply upgrades. Power supply installation information is only intended to assist with the replacement of a defective power supply unit. For your safety, only replace your power supply unit with the one provided by HP Support Services. Powering-Up the Server 1. Turn on power to the monitor connected to the HP Server. Turning on the monitor first ensures that video output auto-configures properly as the server boots up. For information about connecting the monitor, see "Connecting Peripheral Devices" in Chapter 3. 2. Ensure that the Input Voltage selector switch is set for the correct input voltage. 3. Press the Power button on the lower front bezel. See Figure 1-1. When you press the power button on the front bezel, the Server powers up and loads the operating system. The system runs a set of Power On Self Tests (POST) during this process. For details refer to Chapter 8, "Configuring the HP Server" and Chapter 9, "Troubleshooting." 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Chapter 1
Controls and Indicators
Setting the input voltage
Remove the warning label covering the power connector, and ensure that the voltage setting is correct for
your country. (The voltage is set during manufacture and should already be correct.)
Figure 1-4. Input Voltage Selection Switch
Connecting the Power Cords
1.
Connect the power cords to the rear of the monitor and the HP Server. (The connectors are shaped to go
in one way only.)
2.
Connect the monitor’s power cord and the HP Server’s power cord to a grounded outlet. See Figure 1-4.
NOTE
Hewlett-Packard does not support power supply upgrades.
Power supply installation
information is only intended to assist with the replacement of a defective power supply
unit.
For your safety, only replace your power supply unit with the one provided by HP
Support Services.
Powering-Up the Server
1. Turn on power to the monitor connected to the HP Server.
Turning on the monitor first ensures that video output auto-configures properly as the server boots up.
For information about connecting the monitor, see “Connecting Peripheral Devices” in Chapter 3.
2. Ensure that the Input Voltage selector switch is set for the correct input voltage.
3. Press the Power button on the lower front bezel. See Figure 1-1.
When you press the power button on the front bezel, the Server powers up and loads the operating
system. The system runs a set of Power On Self Tests (POST) during this process. For details refer to
Chapter 8, “Configuring the HP Server” and Chapter 9, “Troubleshooting.”
5