HP Tc2110 hp server tc2110 operation and maintenance guide (online version 1.1 - Page 30

Releasing the Retaining Clips, Attaching Side Rails to the Hard Drive

Get HP Tc2110 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Chapter 3 Installing and Configuring Figure 3-6. Releasing the Retaining Clips 5. Remove the hard disk drive from its protective bag and check, or set the following items: a. Check for bent pins on any of the connectors and carefully straighten any bent pins. b. If mounting a SCSI hard drive, ensure it is not terminated and set the SCSI ID jumper for address = ID 1. Refer to the documentation provided with the hard drive. 6. Remove the two side rails from the vacant space in the drive tray and screw them to the new hard drive. See Figure 3-7. The screws are located just above the drive cage. NOTE If the hard disk drive you are planning to install already has a mounting bracket attached, you must remove it in order to attach the side rails to the drive. Figure 3-7: Attaching Side Rails to the Hard Drive 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Chapter 3
Installing and Configuring
Figure 3-6. Releasing the Retaining Clips
5.
Remove the hard disk drive from its protective bag and check, or set the following items:
a.
Check for bent pins on any of the connectors and carefully straighten any bent pins.
b.
If mounting a SCSI hard drive, ensure it is not terminated and set the SCSI ID jumper for address =
ID 1.
Refer to the documentation provided with the hard drive.
6.
Remove the two side rails from the vacant space in the drive tray and screw them to the new hard drive.
See Figure 3-7.
The screws are located just above the drive cage.
NOTE
If the hard disk drive you are planning to install already has a mounting bracket attached,
you must remove it in order to attach the side rails to the drive.
Figure 3-7: Attaching Side Rails to the Hard Drive
24