HP Tc2110 hp server tc2110 operation and maintenance guide (online version 1.1 - Page 37

Use only HP PC133 133 MHz unbuffered ECC SDRAM DIMMs., DIMM Locations on System Board

Get HP Tc2110 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Chapter 3 Installing and Configuring Figure 3-12. DIMM Locations on System Board 6. Remove the new DIMM from its container, handling the module by its edges. Use only HP PC133 (133 MHz) unbuffered ECC SDRAM DIMMs. CAUTION The DIMM should be left in the anti-static container or placed on an anti-static surface, until you are ready to install it into the DIMM slot. 7. Spread the two retaining latches on the slot and align the notches on the DIMM with the keys on the slot. See Figure 3-13. Figure 3-13. DIMM to Slot Alignment 8. Holding the DIMM at 90 degrees to the system board, press the DIMM fully into the slot until the retaining latches close. See Figure 3-14. If the latches do not close, the DIMM is not inserted correctly. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Chapter 3
Installing and Configuring
Figure 3-12. DIMM Locations on System Board
6.
Remove the new DIMM from its container, handling the module by its edges.
Use only HP PC133 (133 MHz) unbuffered ECC SDRAM DIMMs.
CAUTION
The DIMM should be left in the anti-static container or placed on an anti-static surface,
until you are ready to install it into the DIMM slot.
7.
Spread the two retaining latches on the slot and align the notches on the DIMM with the keys on the
slot. See Figure 3-13.
Figure 3-13. DIMM to Slot Alignment
8.
Holding the DIMM at 90 degrees to the system board, press the DIMM fully into the slot until the
retaining latches close. See Figure 3-14.
If the latches do not close, the DIMM is not inserted correctly.
31