HP Tc2110 hp server tc2110 operation and maintenance guide (online version 1.1 - Page 33

See Installing an Optional CD-ROM or DVD Drive

Get HP Tc2110 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Chapter 3 Installing and Configuring 1. If the Server is operating, power down the Server. Refer to Chapter 1, "Controls and Indicators" for instructions. 2. Disconnect the power cord and any external cables connected to the Server. If necessary, label each one to expedite re-assembly. 3. Remove the left side cover. Refer to "Opening and Closing the HP Server" earlier in this chapter. 4. Remove the upper bezel. Refer to "Opening and Closing the HP Server" earlier in this chapter. 5. Press in on both tab latches to release the third drive tray and pull it out at the same time. See Figure 3-10. 6. Remove the RFI shield from the third drive tray. 7. Remove the CD-ROM from the shipping container. 8. Make any settings required by the CD-ROM documentation (primary or slave, etc.). 9. If not already mounted, place the CD-ROM into the CD-ROM tray and secure it using the four screws. 10. Guide the CD-ROM tray into the chassis opening, with the cable connectors of the CD-ROM toward the rear of the chassis. 11. Push the CD-ROM tray all the way into the chassis until the CD-ROM tray snaps into place. The two release tabs should click when in place. 12. At the rear of the CD-ROM, carefully connect the power and data cables. The IDE CD-ROM uses one connector on the cable from the IDE-2 connector, leaving one connector that may be used for an IDE device in the third tray. 13. Replace the upper bezel. 14. Replace the left side cover. 15. Replace the external cables and power cord. Figure 3-10. Installing an Optional CD-ROM or DVD Drive 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Chapter 3
Installing and Configuring
1.
If the Server is operating, power down the Server.
Refer to Chapter 1, “Controls and Indicators” for instructions.
2.
Disconnect the power cord and any external cables connected to the Server.
If necessary, label each one to expedite re-assembly.
3. Remove the left side cover.
Refer to “Opening and Closing the HP Server” earlier in this chapter.
4. Remove the upper bezel.
Refer to “Opening and Closing the HP Server” earlier in this chapter.
5.
Press in on both tab latches to release the third drive tray and pull it out at the same time.
See Figure 3-10.
6.
Remove the RFI shield from the third drive tray.
7.
Remove the CD-ROM from the shipping container.
8.
Make any settings required by the CD-ROM documentation (primary or slave, etc.).
9.
If not already mounted, place the CD-ROM into the CD-ROM tray and secure it using the four screws.
10.
Guide the CD-ROM tray into the chassis opening, with the cable connectors of the CD-ROM toward the
rear of the chassis.
11.
Push the CD-ROM tray all the way into the chassis until the CD-ROM tray snaps into place.
The two release tabs should click when in place.
12.
At the rear of the CD-ROM, carefully connect the power and data cables.
The IDE CD-ROM uses one connector on the cable from the IDE-2 connector, leaving one connector
that may be used for an IDE device in the third tray.
13. Replace the upper bezel.
14. Replace the left side cover.
15.
Replace the external cables and power cord.
Figure 3-10. Installing an Optional CD-ROM or DVD Drive
27