HP Tc2110 hp server tc2110 operation and maintenance guide (online version 1.1 - Page 86

Removing a Hard Disk Drive (Drive Cage Mounted), Releasing the Retaining Clips

Get HP Tc2110 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Chapter 7 Replacing Parts 8. Replace the external cables and power cord. 9. Power on the Server as described in Chapter 1, "Controls and Indicators." Removing a Hard Disk Drive (Drive Cage Mounted) The replacement of the mass storage cage mounted drives is the same for IDE or SCSI devices. The first hard disk drive (IDE or SCSI) is always mounted in the top (shelf 5) of the hard disk drive cage. The second hard disk drive should be mounted just below it (shelf 6). CAUTION Install and remove connectors carefully, and avoid displacing any pins. 1. If the Server is operating, power down the Server. Refer to Chapter 1, "Controls and Indicators" for instructions. 2. Disconnect the power cord and any external cables connected to the Server. If necessary, label each one to expedite re-assembly. 3. Remove the left side cover. 4. Disconnect the data and power connectors from the drive. 5. Press and release the retaining clips at the side of the drive cage. 6. Slide the drive out of the drive cage. Figure 7-6. Releasing the Retaining Clips 7. Remove the four screws to remove the rails from the drive. 8. Place the removed drive in an anti-static bag for protection. 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Chapter 7
Replacing Parts
8.
Replace the external cables and power cord.
9.
Power on the Server as described in Chapter 1, “Controls and Indicators.”
Removing a Hard Disk Drive (Drive Cage Mounted)
The replacement of the mass storage cage mounted drives is the same for IDE or SCSI devices. The first hard
disk drive (IDE or SCSI) is always mounted in the top (shelf 5) of the hard disk drive cage. The second hard
disk drive should be mounted just below it (shelf 6).
CAUTION
Install and remove connectors carefully, and avoid displacing any pins.
1.
If the Server is operating, power down the Server.
Refer to Chapter 1, “Controls and Indicators” for instructions.
2.
Disconnect the power cord and any external cables connected to the Server.
If necessary, label each one to expedite re-assembly.
3. Remove the left side cover.
4.
Disconnect the data and power connectors from the drive.
5.
Press and release the retaining clips at the side of the drive cage.
6.
Slide the drive out of the drive cage.
Figure 7-6. Releasing the Retaining Clips
7.
Remove the four screws to remove the rails from the drive.
8.
Place the removed drive in an anti-static bag for protection.
80