HP Tc2110 hp server tc2110 operation and maintenance guide (online version 1.1 - Page 38

Removing DIMMs, Processor

Get HP Tc2110 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Chapter 3 Installing and Configuring Figure 3-14. DIMM Insertion 9. Repeat Steps 7-8 to install the remaining DIMMs of your memory configuration. Removing DIMMs You may need to remove a DIMM module to downsize your memory configuration or to replace a defective DIMM. 1. If the Server is already installed and working, power down the Server. Refer to Chapter 1, "Controls and Indicators." 2. Disconnect the power cables and all external cables. If necessary, label each one to support re-assembly. WARNING The power supply will continue to provide standby current to the Server until the power cable is disconnected. 3. Remove the left side cover from the Server and lay it aside. Refer to "Opening and Closing the HP Server" earlier in this chapter. 4. Lay the Server on its side with the components up. 5. Open the retaining latches. 6. Lift the DIMM completely away from the slot. 7. Place the DIMM in its anti-static container. 8. Repeat Steps 5-7 for as many DIMMs as you need to remove. 9. When you have completed removal and installation of DIMMs as required, close the Server and restore power. Processor The procedures listed here for removing and replacing a processor and its heat sink-cooling fan are the same for all of the processors used in this HP Server. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
Chapter 3
Installing and Configuring
Figure 3-14. DIMM Insertion
9.
Repeat Steps 7-8 to install the remaining DIMMs of your memory configuration.
Removing DIMMs
You may need to remove a DIMM module to downsize your memory configuration or to replace a defective
DIMM.
1.
If the Server is already installed and working, power down the Server.
Refer to Chapter 1, “Controls and Indicators.”
2.
Disconnect the power cables and all external cables.
If necessary, label each one to support re-assembly.
WARNING
The power supply will continue to provide standby current to the Server until the power
cable is disconnected.
3.
Remove the left side cover from the Server and lay it aside.
Refer to “Opening and Closing the HP Server” earlier in this chapter.
4.
Lay the Server on its side with the components up.
5. Open the retaining latches.
6.
Lift the DIMM completely away from the slot.
7.
Place the DIMM in its anti-static container.
8.
Repeat Steps 5-7 for as many DIMMs as you need to remove.
9.
When you have completed removal and installation of DIMMs as required, close the Server and restore
power.
Processor
The procedures listed here for removing and replacing a processor and its heat sink-cooling fan are the same
for all of the processors used in this HP Server.
32