HP XM600 hp kayak xm600 series 1, user's guide for desktop models - Page 31

Removing and Replacing a PCI Accessory Card, Install an Accessory Card - kayak manual

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing a PCI Accessory Card Removing and Replacing a PCI Accessory Card The HP Kayak XM600 has five 32-bit 33 MHz PCI accessory card slots and one AGP slot on the system board. The AGP slot accepts standard 25 W AGP video cards. NOTE Higher power AGP PRO video cards cannot be used in desktop models. Hardware Protection on the system board ensures that the system is protected against this. NOTE 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover (refer to page 22 for instructions). 3 If you intend to: a Install an Accessory Card: Unscrew and remove the slot panel. Store it in a safe place. If the slot cover is tight, loosen the screws on the adjacent slots. b Replace an Accessory Card: Remove any cables connected to the accessory card. Remove the screw that holds the old card in place and carefully pull it out. Some cards may have preferred locations and special installation instructions detailed in their manuals. 4 Aligning the new card carefully, slide it into position, then press it firmly into the slot and tighten the retaining screw. 5 Install any other accessories before replacing the cover (refer to page 23). Reconnect all the power and telecommunications cables. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
2
Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing a PCI Accessory Card
31
Removing and Replacing a PCI Accessory Card
The HP Kayak XM600 has five 32-bit 33 MHz PCI accessory card slots and
one AGP slot on the system board. The AGP slot accepts standard 25 W
AGP video cards.
NOTE
Higher power AGP PRO video cards cannot be used in desktop models.
Hardware Protection on the system board ensures that the system is
protected against this.
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover (refer to page 22 for instructions).
3
If you intend to:
a
Install an Accessory Card:
Unscrew and remove the slot panel. Store it in a safe place. If the slot
cover is tight, loosen the screws on the adjacent slots.
b
Replace an Accessory Card:
Remove any cables connected to the accessory card. Remove the
screw that holds the old card in place and carefully pull it out.
NOTE
Some cards may have preferred locations and special installation
instructions detailed in their manuals.
4
Aligning the new card carefully, slide it into position, then press it firmly
into the slot and tighten the retaining screw.
5
Install any other accessories before replacing the cover (refer to page
23). Reconnect all the power and telecommunications cables.