HP XM600 hp kayak xm600 series 1, user's guide for desktop models - Page 47

Replacing the System Board, Removing the, System Board

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Replacing the System Board Removing the System Board Replacing the System Board 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front bezel (refer to page 23 for these instructions). 3 Remove the HP UltraFlow Airflow Guide (refer to page 24 for instructions). 4 Disconnect any cables attached to the system board. 5 Move the front access cage forward (described on page 37). 6 Remove the main memory, processor and any accessory cards from the old system board (described in this chapter). 7 Remove the screw located on the rear panel near the AGP slot. 8 Lift the system board out, being careful not to damage the PC's rear connectors. 9 Unclip the retaining bracket from the system board. This bracket must be re-installed on the new system board (refer to the diagram on the following page).  ò 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
2
Installing and Replacing Hardware Parts in Your PC Workstation
Replacing the System Board
47
Replacing the System Board
Removing the
System Board
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover and front bezel (refer to page 23 for
these instructions).
3
Remove the HP UltraFlow Airflow Guide (refer to page 24 for
instructions).
4
Disconnect any cables attached to the system board.
5
Move the front access cage forward (described on page 37).
6
Remove the main memory, processor and any accessory cards from the
old system board (described in this chapter).
7
Remove the screw located on the rear panel near the AGP slot
.
8
Lift the system board out, being careful not to damage the PC’s rear
connectors.
9
Unclip the retaining bracket from the system board. This bracket must
be re-installed on the new system board (refer to the diagram on the
following page).
ò