HP XM600 hp kayak xm600 series 1, user's guide for desktop models - Page 35

Removing and Replacing the Primary Hard Disk Drive, Removing the, Old Drive, Installing the, New Drive

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Removing and Replacing the Primary Hard Disk Drive CAUTION Removing the Old Drive Removing and Replacing the Primary Hard Disk Drive Handle the hard disk drive with care. Avoid shocks and violent movement as this can cause damage to the hard disk drive's internal components. Make sure that you back up your files before you install a hard disk drive. Refer to your operating system documentation for information on how to do this. 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front bezel (refer to page 23 for these instructions). 3 Remove the two retaining screws from the chassis located on the front of the PC and pull the primary hard disk drive out of the hard disk drive bay. CAUTION Installing the New Drive 4 Disconnect the data and power cables from the hard disk drive. Take care when handling the hard disk drive during installation. A onequarter inch drop can damage it. 1 Connect the data and power connectors to the hard disk drive. 2 Slide the new drive into the hard disk drive bay (with the correct orientation) and tighten the two retaining screws you removed earlier. 3 Replace the front bezel and PC Workstation's cover (refer to page 23). Reconnect all the power and telecommunications cables. 4 Turn to page 44 to complete the installation. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
2
Installing and Replacing Hardware Parts in Your PC Workstation
Removing and Replacing the Primary Hard Disk Drive
35
Removing and Replacing the Primary Hard Disk Drive
CAUTION
Handle the hard disk drive with care. Avoid shocks and violent
movement as this can cause damage to the hard disk drive’s internal
components.
Make sure that you back up your files before you install a hard disk
drive. Refer to your operating system documentation for information on
how to do this.
Removing the
Old Drive
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover and front bezel (refer to page 23 for
these instructions).
3
Remove the two retaining screws from the chassis located on the front
of the PC and pull the primary hard disk drive out of the hard disk drive
bay.
4
Disconnect the data and power cables from the hard disk drive.
CAUTION
Take care when handling the hard disk drive during installation. A one-
quarter inch drop can damage it.
Installing the
New Drive
1
Connect the data and power connectors to the hard disk drive.
2
Slide the new drive into the hard disk drive bay (with the correct
orientation) and tighten the two retaining screws you removed earlier.
3
Replace the front bezel and PC Workstation’s cover (refer to page 23).
Reconnect all the power and telecommunications cables.
4
Turn to page 44 to complete the installation.