HP XM600 hp kayak xm600 series 1, user's guide for desktop models - Page 44

Completing the Installation of a Mass Storage Device, When a SCSI Hard

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Completing the Installation of a Mass Storage Device When an IDE Drive Is Installed When a SCSI Hard Disk Drive Is Installed When a CD-ROM, CD-RW or DV-Drive is Installed When a Floppy Disk Drive Is Installed Completing the Installation of a Mass Storage Device 1 Switch on the PC Workstation. 2 If an error message appears, follow the instructions provided by the Error Message Utility. 3 To verify the configuration of your hard disk drive, press to enter Setup when prompted. Once in Setup, select the Advanced menu, then the IDE Devices submenu. In the Primary Master item, check that the details for the device have been correctly detected by the Setup program. 4 Press to save and exit Setup. 5 Refer to the operating system documentation for information on formatting a drive. 6 If an IDE drive is removed, switch on the PC Workstation. The system BIOS will detect that the device is missing. Press to confirm that you want to remove the device. The system configuration will be updated automatically. 1 Switch on the PC Workstation. 2 To enter the SCSI Configuration Utility press when the message Press to start Configuration Utility... is displayed during the PC Workstation's start-up routine. 3 Verify or modify the configuration of your new SCSI hard disk drive. For more information on configuring a SCSI hard disk drive, refer to the SCSI Administrator's Guide available on HP's web site at http://www.hp.com/go/kayaksupport. 4 When configuration is complete, exit the SCSI Configuration Utility and re-boot the PC Workstation to save any changes. 1 Switch on the PC Workstation and press when Setup appears. 2 In the Setup program, select the Advanced menu, the IDE Devices submenu. Check that the CD-ROM drive has been detected on the IDE channel. 3 Press to save and exit the program. 1 Switch on the PC Workstation and press when Setup appears. 2 In the Setup program, select the Advanced menu, the Floppy Disk Drives submenu, and check that the drive has been detected. 3 Press to save and exit the program. 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
2
Installing and Replacing Hardware Parts in Your PC Workstation
Completing the Installation of a Mass Storage Device
44
Completing the Installation of a Mass Storage Device
When an IDE Drive
Is Installed
1
Switch on the PC Workstation.
2
If an error message appears, follow the instructions provided by the
Error Message Utility.
3
To verify the configuration of your hard disk drive, press
to enter
Setup
when prompted. Once in
Setup
, select the
Advanced
menu, then
the
IDE Devices
submenu. In the
Primary Master
item, check that the details
for the device have been correctly detected by the
Setup
program.
4
Press
to save and exit
Setup
.
5
Refer to the operating system documentation for information on
formatting a drive.
6
If an IDE drive is removed, switch on the PC Workstation. The system
BIOS will detect that the device is missing. Press
to confirm that you
want to remove the device. The system configuration will be updated
automatically.
When a SCSI Hard
Disk Drive Is
Installed
1
Switch on the PC Workstation.
2
To enter the SCSI Configuration Utility press
when the message
Press
to start Configuration Utility...
is displayed during the PC
Workstation’s start-up routine.
3
Verify or modify the configuration of your new SCSI hard disk drive.
For more information on configuring a SCSI hard disk drive, refer
to the
SCSI Administrator’s Guide
available on HP’s web site at
.
4
When configuration is complete, exit the SCSI Configuration Utility and
re-boot the PC Workstation to save any changes.
When a CD-ROM,
CD-RW or DV-Drive
is Installed
1
Switch on the PC Workstation and press
when
Setup
appears.
2
In the
Setup
program, select the
Advanced
menu, the
IDE Devices
submenu. Check that the CD-ROM drive has been detected on the IDE
channel.
3
Press
to save and exit the program.
When a Floppy Disk
Drive Is Installed
1
Switch on the PC Workstation and press
when
Setup
appears.
2
In the
Setup
program, select the
Advanced
menu, the
Floppy Disk Drives
submenu, and check that the drive has been detected.
3
Press
to save and exit the program
.