HP XM600 hp kayak xm600 series 1, user's guide for desktop models - Page 34

Before Installing a, SCSI Hard Disk, Selected Models, you should con an

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Installing Mass Storage Devices Before Installing a SCSI Hard Disk (Selected Models Only) NOTE If you are installing an additional SCSI drive, you should configure an unused SCSI ID to this accessory. SCSI IDs range from 0 to 15 for Ultrawide 16-bit SCSI. SCSI ID 0 is used by the first SCSI hard disk drive and SCSI ID 7 is reserved for the integrated SCSI controller (the default for narrow and wide SCSI devices). You do not need to select a SCSI ID for Plug and Play SCSI hard disks (SCSI hard disks that support the SCAM protocol). The total length of the external SCSI cables should not exceed 3 meters (approximately 10 feet). You should assign an unused SCSI ID to the second SCSI hard disk drive (for example, SCSI ID 1). The SCSI ID is usually configured with jumpers on the SCSI hard disk drive. Refer to the installation guide supplied with the drive for information on selecting a SCSI ID. Some internal SCSI disk drives may have termination resistors that must be removed or disabled before installation in your PC Workstation. Refer to the drive's installation guide for more details and to see if there is a special installation procedure to follow. 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
2
Installing and Replacing Hardware Parts in Your PC Workstation
Installing Mass Storage Devices
34
Before Installing a
SCSI Hard Disk
(Selected Models
Only)
If you are installing an additional SCSI drive,
you should configure an
unused SCSI ID to this accessory.
SCSI IDs range from 0 to 15 for
Ultrawide 16-bit SCSI. SCSI ID 0 is used by the first SCSI hard disk drive
and SCSI ID 7 is reserved for the integrated SCSI controller (the default for
narrow and wide SCSI devices).
NOTE
You do not need to select a SCSI ID for Plug and Play SCSI hard disks
(SCSI hard disks that support the SCAM protocol).
The total length of the external SCSI cables should not exceed 3 meters
(approximately 10 feet).
You should assign an unused SCSI ID to the second SCSI hard disk drive
(for example, SCSI ID 1).
The SCSI ID is usually configured with jumpers on the SCSI hard disk drive.
Refer to the installation guide supplied with the drive for information on
selecting a SCSI ID.
Some internal SCSI disk drives may have termination resistors that must be
removed or disabled before installation in your PC Workstation. Refer to
the drive’s installation guide for more details and to see if there is a special
installation procedure to follow.