HP XM600 hp kayak xm600 series 1, user's guide for desktop models - Page 37

Installing an Accessory in the Front Access Cage

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Installing an Accessory in the Front Access Cage Installing an Accessory in the Front Access Cage 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and the front bezel (refer to page 22 for instructions). 3 Remove the HP UltraFlow Airflow Guide (refer to page 24). 4 Remove the retaining screw from the front access cage, and slide it forwards until it stops. 5 Disconnect the power and data cables from the installed drives. 6 Lift the front access cage upwards and out from the PC. Place the cage on a table/desk top. 7 Remove the 5.25-inch plastic filler plate. Use a screwdriver to unclip the two latches located on the left-hand side of the filler plate, then pivot it out. Store the filler plate in a safe place for future use. Be very careful not to hurt your fingers when you remove the plate. 8 If the new drive has a tray, attach the drive to the front access cage. Many devices, such as the HP Zip drive, require an HP-supplied tray before they can be installed. CD-ROM drives do not require a tray. 9 Slide the new drive into the shelf. Ensure that the front of the new drive is aligned with an existent device or filler plate. Secure the drive in position using the screws supplied with it. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
2
Installing and Replacing Hardware Parts in Your PC Workstation
Installing an Accessory in the Front Access Cage
37
Installing an Accessory in the Front Access Cage
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover and the front bezel (refer to page 22
for instructions).
3
Remove the HP UltraFlow Airflow Guide (refer to page 24).
4
Remove the retaining screw from the front access cage, and slide it
forwards until it stops.
5
Disconnect the power and data cables from the installed drives.
6
Lift the front access cage upwards and out from the PC. Place the cage
on a table/desk top.
7
Remove the 5.25-inch plastic filler plate. Use a screwdriver to unclip the
two latches located on the left-hand side of the filler plate, then pivot it
out. Store the filler plate in a safe place for future use
.
Be very careful
not to hurt your fingers when you remove the plate.
8
If the new drive has a tray, attach the drive to the front access cage.
Many devices, such as the HP Zip drive, require an HP-supplied tray
before they can be installed. CD-ROM drives do not require a tray.
9
Slide the new drive into the shelf. Ensure that the front of the new drive
is aligned with an existent device or filler plate. Secure the drive in
position using the screws supplied with it.