HP rp7405 User Guide, Third Edition - hp rp7405/rp7410 Servers - Page 50

Lifting the Server, installing server into the rack

Get HP rp7405 PDF manuals and user guides View all HP rp7405 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Installation Unpacking the Server Step 6. Continue to pull the handles apart until the spring plunger snaps into final position. The spring plunger will drop down into the recess position. Step 7. Check that the handles are secure by pressing the handles together and moving back and forth. Check to see if lift handle panel breaks free of chassis. Step 8. Repeat the steps above for the other handle Step 9. To lift the server, rotate the handles 90 degrees to horizontal position. NOTE If you are installing the system in a rack, refer to the installation guide, hp J1530A, rack installation kit (lower case intended). Step 10. After moving the server, remove the lift handle panels from the chassis and reinstall the server covers and front bezel. Refer to installation guide, hp J1530A, rack installation kit (lower case intended). Figure 2-13 Lifting the Server Installing Server Into the Rack Any hp rp7405/rp7410 server that is to be installed into a rack is shipped with equipment slides. With every set of slides comes an installation guide: installation guide, hp J1530A, rack installation kit (lower case intended). Follow the steps in this installation guide to determine where and how to place the server into the rack. 28 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 2
Installation
Unpacking the Server
28
Step 6.
Continue to pull the handles apart until the spring plunger snaps into final position. The spring
plunger will drop down into the recess position.
Step 7.
Check that the handles are secure by pressing the handles together and moving back and forth.
Check to see if lift handle panel breaks free of chassis.
Step 8.
Repeat the steps above for the other handle
Step 9.
To lift the server, rotate the handles 90 degrees to horizontal position.
NOTE
If you are installing the system in a rack, refer to the
installation guide, hp J1530A,
rack installation kit
(lower case intended).
Step 10.
After moving the server, remove the lift handle panels from the chassis and reinstall the server
covers and front bezel. Refer to
installation guide, hp J1530A, rack installation kit
(lower case
intended).
Figure 2-13 Lifting the Server
Installing Server Into the Rack
Any hp rp7405/rp7410 server that is to be installed into a rack is shipped with equipment slides. With every
set of slides comes an installation guide:
installation guide, hp J1530A, rack installation kit
(lower case
intended). Follow the steps in this installation guide to determine where and how to place the server into the
rack.