HP rp7405 User Guide, Third Edition - hp rp7405/rp7410 Servers - Page 98

Removing a BPS, BPS Detail, BPS Detail

Get HP rp7405 PDF manuals and user guides View all HP rp7405 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Removal and Replacement Removing and Replacing a Bulk Power Supply Removing a BPS Figure 4-15 BPS Detail Step 1. Pull the extraction levers located on the upper front outer portion of the BPS. Step 2. Slide the BPS forward using the extractions levers to remove it from the chassis. Replacing a BPS Step 1. Verify that the extraction levers are in the open position, then insert the BPS into the empty slot. NOTE The BPS easily slides into the chassis; however, a slow firm pressure will be needed to properly seat the connection. Step 2. Ensure the BPS has seated by closing the extraction levers. NOTE BPS LED should show BPS operational and no fault. BPS LED should be GREEN. 76 Chapter 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Chapter 4
Removal and Replacement
Removing and Replacing a Bulk Power Supply
76
Removing a BPS
Figure 4-15
BPS Detail
Step 1.
Pull the extraction levers located on the upper front outer portion of the BPS.
Step 2.
Slide the BPS forward using the extractions levers to remove it from the chassis.
Replacing a BPS
Step 1.
Verify that the extraction levers are in the open position, then insert the BPS into the empty slot.
NOTE
The BPS easily slides into the chassis; however, a slow firm pressure will be needed
to properly seat the connection.
Step 2.
Ensure the BPS has seated by closing the extraction levers.
NOTE
BPS LED should show BPS operational and no fault. BPS LED should be GREEN.