HP xp8000 HP L1581A advanced connectivity module - (English) User Guide - Page 56

Setup problems, If you cannot change settings using a Web browser

Get HP xp8000 - Digital Projector PDF manuals and user guides View all HP xp8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Fixing the System an Infrastructure connection. For more details, see Chapter 2, "Presenting from a Networked Computer," on page 17 or Chapter 3, "Presenting from a Wireless Handheld Organizer," on page 29. If the projector's network configuration is completely wrong and you cannot fix it: ❏ Reset the projector's network configuration to the factory default values. To do this, turn off the projector and allow it to cool, then turn off the main disconnect switch. Insert a straightened paperclip into the small hole on the module below near the USB ports. While pressing the small button inside, turn on the main switch and continue holding the button for at least 15 seconds. ❏ Contact your network administrator to determine the proper settings for your network. Setup problems If you cannot change settings using a Web browser: ❏ If you cannot connect to the projector using a Web browser, see the previous problem above. ❏ If you cannot access or edit certain pages, the Web interface has been protected by the Web administrator. Contact the administrator. ❏ If the administrator password has been forgotten, reset the network configuration to the factory default values. See the previous problem above. If you cannot install Wireless Presenter-to-Go on your computer: ❏ Be sure your computer meets the minimum requirements for Wireless Presenter-to-Go. See "To prepare your computer for networked presentations" on page 18 for more information. ❏ If an earlier version of HP Wireless Presenter-to-Go is installed on your computer, try uninstalling it before installing a new version. 56 User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
56
User’s Guide
Fixing the System
an Infrastructure connection. For more details, see Chapter 2,
“Presenting from a Networked Computer,” on page 17 or Chapter
3, “Presenting from a Wireless Handheld Organizer,” on page 29.
If the projector’s network configuration is completely wrong and you cannot
fix it:
❏
Reset the projector’s network configuration to the factory default
values. To do this, turn off the projector and allow it to cool,
then turn off the main disconnect switch. Insert a straightened
paperclip into the small hole on the module below near the USB
ports. While pressing the small button inside, turn on the main
switch and continue holding the button for at least 15 seconds.
❏
Contact your network administrator to determine the proper
settings for your network.
Setup problems
If you cannot change settings using a Web browser:
❏
If you cannot connect to the projector using a Web browser, see
the previous problem above.
❏
If you cannot access or edit certain pages, the Web interface
has been protected by the Web administrator. Contact the
administrator.
❏
If the administrator password has been forgotten, reset the
network configuration to the factory default values. See the
previous problem above.
If you cannot install Wireless Presenter-to-Go on your computer:
❏
Be sure your computer meets the minimum requirements for
Wireless Presenter-to-Go. See “To prepare your computer for
networked presentations” on page 18 for more information.
❏
If an earlier version of HP Wireless Presenter-to-Go is installed
on your computer, try uninstalling it before installing a new
version.