IBM 8658 User Guide - Page 60

Removing, server, tower, model

Get IBM 8658 - Eserver xSeries 230 PDF manuals and user guides
UPC - 087944602644
View all IBM 8658 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

1 Top cover 2 Right side latch 3 Cover release lever 4 Left side latch To remove the server top cover: 1. Review the information in "Before you begin" on page 46. 2. If you are planning to install or remove any part other than a hot-swap hard disk drive or hot-swap power supply, turn off the server and all attached devices and disconnect all external cables and power cords. 3. Release the left and right side latches and pull the server out of the rack enclosure until both slide rails lock. Note: When the server is in the locked position, you can reach the cables on the back of the server. 4. Move the cover-release lever down while sliding the top cover toward the rear of the server about 25 mm (1 inch). Lift the cover off the server and set the cover aside. Attention: For proper cooling and airflow, replace the cover before turning on the server. Operating the server for extended periods of time (over 30 minutes) with the cover removed might damage server components. Removing the server door (tower model) 1 Release tab 2 Door 3 Flange To remove the server door: 1. Unlock and open the server door. 2. Locate the flange on the top edge of the door. 50 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
±1²
Top
cover
±2²
Right
side
latch
±3²
Cover
release
lever
±4²
Left
side
latch
To
remove
the
server
top
cover:
1.
Review
the
information
in
“Before
you
begin”
on
page
46.
2.
If
you
are
planning
to
install
or
remove
any
part
other
than
a
hot-swap
hard
disk
drive
or
hot-swap
power
supply,
turn
off
the
server
and
all
attached
devices
and
disconnect
all
external
cables
and
power
cords.
3.
Release
the
left
and
right
side
latches
and
pull
the
server
out
of
the
rack
enclosure
until
both
slide
rails
lock.
Note:
When
the
server
is
in
the
locked
position,
you
can
reach
the
cables
on
the
back
of
the
server.
4.
Move
the
cover-release
lever
down
while
sliding
the
top
cover
toward
the
rear
of
the
server
about
25
mm
(1
inch).
Lift
the
cover
off
the
server
and
set
the
cover
aside.
Attention:
For
proper
cooling
and
airflow,
replace
the
cover
before
turning
on
the
server.
Operating
the
server
for
extended
periods
of
time
(over
30
minutes)
with
the
cover
removed
might
damage
server
components.
Removing
the
server
door
(tower
model)
±1²
Release
tab
±2²
Door
±3²
Flange
To
remove
the
server
door:
1.
Unlock
and
open
the
server
door.
2.
Locate
the
flange
on
the
top
edge
of
the
door.
50
:
Netfinity
5100
Type
8658
Models
11Y,
21Y,
31Y,
41Y,
51Y,
1RY,
2RY,
3RY,
4RY,
5RY