IBM 8658 User Guide - Page 68

Replacing, drive, hot-swap

Get IBM 8658 - Eserver xSeries 230 PDF manuals and user guides
UPC - 087944602644
View all IBM 8658 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Attention: To maintain proper system cooling, do not operate the server for more than two minutes without either a drive or a filler panel installed for each bay. To install a drive in a hot-swap drive bay: 1. If your hard disk drive is not installed on the drive tray, place the drive in the drive tray and, being careful not to over-tighten the screws, attach the drive to the tray using the four screws provided with the option kit. 2. Remove the filler panel from one of the empty hot-swap bays by inserting your finger into the depression at the left side of the filler panel and pulling it away from the server. Note: If you are installing a half-high hard disk drive, you will need to remove two adjacent filler panels. The two filler panels should be from either the top pair of bays, the middle pair of bays, or the bottom pair of bays. 3. Install the hard disk drive in the hot-swap bay: a. Ensure the tray handle is open (that is, perpendicular to the drive). b. Align the rails on the drive/tray assembly with the guide rails in the drive bay. c. Gently push the drive/tray assembly into the bay until the drive connects to the backplane. d. Push the tray handle toward the closed position until it locks the drive in place. 4. If you installed a half-high hard disk drive, install a filler panel in the gap above the drive: a. Locate the slim filler bezel that is designed for use with half-high drives. It is stored on the empty tray of the filler panel that you removed earlier in this procedure. b. Pull the slim filler bezel off the filler panel. c. Gently push the slim filler bezel into place in the gap above the drive. 5. Check the hard disk drive status indicators to verify that the hard disk drives are operating properly (see "Server controls and indicators" on page 7 for the location of the status indicators). v When the amber light is on continuously, the drive has failed. v When the amber light flashes slowly (one flash per second), the drive is being rebuilt. v When the amber light flashes rapidly (three flashes per second), the controller is identifying the drive. v If you have a RAID adapter installed, when the green Activity light is on continuously the drive is ready. Note: If your server has a RAID adapter installed, refer to the information provided with the RAID adapter for information about adding a drive. Replacing a drive in a hot-swap bay You do not have to turn off the server to remove or install the hot-swap drives. Attention: 1. Before you remove a hot-swap hard disk drive that is not defective, back up all important data. 58 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
Attention:
To
maintain
proper
system
cooling,
do
not
operate
the
server
for
more
than
two
minutes
without
either
a
drive
or
a
filler
panel
installed
for
each
bay.
To
install
a
drive
in
a
hot-swap
drive
bay:
1.
If
your
hard
disk
drive
is
not
installed
on
the
drive
tray,
place
the
drive
in
the
drive
tray
and,
being
careful
not
to
over-tighten
the
screws
,
attach
the
drive
to
the
tray
using
the
four
screws
provided
with
the
option
kit.
2.
Remove
the
filler
panel
from
one
of
the
empty
hot-swap
bays
by
inserting
your
finger
into
the
depression
at
the
left
side
of
the
filler
panel
and
pulling
it
away
from
the
server.
Note:
If
you
are
installing
a
half-high
hard
disk
drive,
you
will
need
to
remove
two
adjacent
filler
panels.
The
two
filler
panels
should
be
from
either
the
top
pair
of
bays,
the
middle
pair
of
bays,
or
the
bottom
pair
of
bays.
3.
Install
the
hard
disk
drive
in
the
hot-swap
bay:
a.
Ensure
the
tray
handle
is
open
(that
is,
perpendicular
to
the
drive).
b.
Align
the
rails
on
the
drive/tray
assembly
with
the
guide
rails
in
the
drive
bay.
c.
Gently
push
the
drive/tray
assembly
into
the
bay
until
the
drive
connects
to
the
backplane.
d.
Push
the
tray
handle
toward
the
closed
position
until
it
locks
the
drive
in
place.
4.
If
you
installed
a
half-high
hard
disk
drive,
install
a
filler
panel
in
the
gap
above
the
drive:
a.
Locate
the
slim
filler
bezel
that
is
designed
for
use
with
half-high
drives.
It
is
stored
on
the
empty
tray
of
the
filler
panel
that
you
removed
earlier
in
this
procedure.
b.
Pull
the
slim
filler
bezel
off
the
filler
panel.
c.
Gently
push
the
slim
filler
bezel
into
place
in
the
gap
above
the
drive.
5.
Check
the
hard
disk
drive
status
indicators
to
verify
that
the
hard
disk
drives
are
operating
properly
(see
“Server
controls
and
indicators”
on
page
7
for
the
location
of
the
status
indicators).
v
When
the
amber
light
is
on
continuously,
the
drive
has
failed.
v
When
the
amber
light
flashes
slowly
(one
flash
per
second),
the
drive
is
being
rebuilt.
v
When
the
amber
light
flashes
rapidly
(three
flashes
per
second),
the
controller
is
identifying
the
drive.
v
If
you
have
a
RAID
adapter
installed,
when
the
green
Activity
light
is
on
continuously
the
drive
is
ready.
Note:
If
your
server
has
a
RAID
adapter
installed,
refer
to
the
information
provided
with
the
RAID
adapter
for
information
about
adding
a
drive.
Replacing
a
drive
in
a
hot-swap
bay
You
do
not
have
to
turn
off
the
server
to
remove
or
install
the
hot-swap
drives.
Attention:
1.
Before
you
remove
a
hot-swap
hard
disk
drive
that
is
not
defective,
back
up
all
important
data.
58
:
Netfinity
5100
Type
8658
Models
11Y,
21Y,
31Y,
41Y,
51Y,
1RY,
2RY,
3RY,
4RY,
5RY