IBM 8658 User Guide - Page 70

Installing, non-hot-swap, drive

Get IBM 8658 - Eserver xSeries 230 PDF manuals and user guides
UPC - 087944602644
View all IBM 8658 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

6. Place the new hard disk drive on the hot-swap tray and, being careful not to over-tighten the screws, attach the drive to the tray using four screws. 7. Install the hard disk drive in the hot-swap bay: a. Ensure the tray handle is open (that is, perpendicular to the drive). b. Align the rails on the drive/tray assembly with the guide rails in the drive bay. c. Gently push the drive/tray assembly into the bay until the drive connects to the backplane. d. Push the tray handle toward the closed position until it locks the drive in place. 8. Check the hard disk drive status indicators to verify that the hard disk drive is installed properly (see "Server controls and indicators" on page 7 for the location of the status indicators). v When the amber light is on continuously, the drive has failed. v When the amber light flashes slowly (one flash per second), the drive is being rebuilt. v When the amber light flashes rapidly (three flashes per second), the controller is identifying the drive. v If you have a RAID adapter installed, when the green Activity light is on continuously the drive is ready 9. If your server is a tower model, close and lock the server door. Installing a non-hot-swap drive Note: The server's EMI integrity and cooling are both protected by having the non-hot-swap bays covered or occupied. When you install a drive, save the filler panel from the bay, in case you later remove the drive and do not replace it with another. 1 Non-hot-swap bay 2 Blue slide rails 3 Filler panel 4 Non-hot-swap drive 5 Slide rails To install a non-hot-swap drive in one of the non-hot-swap bays: 60 : Netfinity 5100 Type 8658 Models 11Y, 21Y, 31Y, 41Y, 51Y, 1RY, 2RY, 3RY, 4RY, 5RY

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
6.
Place
the
new
hard
disk
drive
on
the
hot-swap
tray
and,
being
careful
not
to
over-tighten
the
screws
,
attach
the
drive
to
the
tray
using
four
screws.
7.
Install
the
hard
disk
drive
in
the
hot-swap
bay:
a.
Ensure
the
tray
handle
is
open
(that
is,
perpendicular
to
the
drive).
b.
Align
the
rails
on
the
drive/tray
assembly
with
the
guide
rails
in
the
drive
bay.
c.
Gently
push
the
drive/tray
assembly
into
the
bay
until
the
drive
connects
to
the
backplane.
d.
Push
the
tray
handle
toward
the
closed
position
until
it
locks
the
drive
in
place.
8.
Check
the
hard
disk
drive
status
indicators
to
verify
that
the
hard
disk
drive
is
installed
properly
(see
“Server
controls
and
indicators”
on
page
7
for
the
location
of
the
status
indicators).
v
When
the
amber
light
is
on
continuously,
the
drive
has
failed.
v
When
the
amber
light
flashes
slowly
(one
flash
per
second),
the
drive
is
being
rebuilt.
v
When
the
amber
light
flashes
rapidly
(three
flashes
per
second),
the
controller
is
identifying
the
drive.
v
If
you
have
a
RAID
adapter
installed,
when
the
green
Activity
light
is
on
continuously
the
drive
is
ready
9.
If
your
server
is
a
tower
model,
close
and
lock
the
server
door.
Installing
a
non-hot-swap
drive
Note:
The
server’s
EMI
integrity
and
cooling
are
both
protected
by
having
the
non-hot-swap
bays
covered
or
occupied.
When
you
install
a
drive,
save
the
filler
panel
from
the
bay,
in
case
you
later
remove
the
drive
and
do
not
replace
it
with
another.
±1²
Non-hot-swap
bay
±2²
Blue
slide
rails
±3²
Filler
panel
±4²
Non-hot-swap
drive
±5²
Slide
rails
To
install
a
non-hot-swap
drive
in
one
of
the
non-hot-swap
bays:
60
:
Netfinity
5100
Type
8658
Models
11Y,
21Y,
31Y,
41Y,
51Y,
1RY,
2RY,
3RY,
4RY,
5RY