Home » IBM Manuals » Desktops » IBM 88554RU » Manual Viewer

IBM 88554RU Installation Guide - Page 121

Warning: Data on Secondary or Hot Spare! Mirroring will overwrite, LSI Logic MPT SCSI Setup Utility

Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

3. Select RAID Properties and press Enter. If you have already configured RAID there will be an additional screen that allows you to Modify, Sync, or Delete the RAID array. LSI Logic MPT SCSI Setup Utility Version v1.02.11 RAID Properties Array: IM SCSI ID: 0 Size(MB): 17278 SCSI Device Identifier Array Hot Status Predict Size ID Disk? Spare Failure (MB) 0 IBM-PSG ST318451LC !#B833 [Yes] [No] Primary No 17278 1 IBM-ESXSST318452LC !#B841 [Yes] [No] Secondary No 17278 2 - 3 - 4 - 5 - 6 - 7 53C1030 8 IBM 25P3495a S320 11 Incompatbl-- ------ 9 - 10 - 11 - 12 - 13 - 14 - 15 - F1/Shift+1 =Help ArrowKeys/H,J,K,L =Select Item -/+ =Change [Item] Esc=Exit Menu Home(I)/End(0) =Select Item Enter=Execute Figure 4-12 Configuring RAID 1 4. Change the Array Disk options for SCSI IDs 0 and 1 to Yes. These are the two internal hard disks. Normally SCSI ID 0 is the primary disk, but this may not be the case. All other devices will either have nothing in the Status column, or will say Incompatbl. In both cases these devices cannot be used as part of a RAID configuration. 5. Once all the configuration changes are made press Esc.The following message appears: Warning: Data on Secondary or Hot Spare! Mirroring will overwrite! 6. Confirm by pressing Enter and continue. 7. Save the changes on the next window and exit the menu. The disks will synchronize in the background. Chapter 4. Installation 107

Section	Page
Front cover	1
Contents	5
Notices	9
Trademarks	10
Preface	11
The team that wrote this redbook	11
Become a published author	13
Comments welcome	14
Chapter 1. Technical description	15
1.1 Features	16
1.1.1 Comparing the x455 with the x450	16
1.1.2 Features not supported	17
1.2 The x455 base models	18
1.2.1 Front and rear views	18
1.3 System assembly	20
1.4 IBM XA-64 chipset	21
1.4.1 The processor-board assembly	23
1.4.2 The memory-board assembly	27
1.4.3 PCI-X board assembly	31
1.5 Remote Supervisor Adapter	33
1.6 RXE-100 Expansion Enclosure	35
1.7 Multinode scalable partitions	36
1.7.1 RXE-100 connectivity	38
1.7.2 Multinode configuration	39
1.7.3 Integrated I/O function support	40
1.7.4 Error recovery	40
1.8 Redundancy	41
1.9 Light path diagnostics	41
1.10 Extensible Firmware Interface	43
1.10.1 GUID Partition Table disk	45
1.10.2 EFI System Partition	47
1.10.3 EFI and the reduced-legacy concept	48
1.11 Operating system support	49
1.12 Enterprise X-Architecture	49
1.12.1 NUMA architecture	50
Chapter 2. Positioning	53
2.1 Migrating to a 64-bit platform	54
2.2 Scalable system partitioning	55
2.2.1 RXE-100 Expansion Enclosure	56
2.3 Operating system support	56
2.4 Server consolidation	57
2.5 ServerProven®	58
2.6 IBM Datacenter Solution Program	59
2.7 Application solutions	60
2.7.1 Database applications	60
2.7.2 Business logic	62
2.7.3 e-Business and security transactions	64
2.7.4 In-house developed compute-intensive applications	65
2.7.5 Science and technology industries	65
2.8 Why choose x455	66
Chapter 3. Planning	69
3.1 System hardware	70
3.1.1 Processors	70
3.1.2 Memory	71
3.1.3 PCI-X slot configuration	75
3.1.4 Broadcom Gigabit Ethernet controller	78
3.2 Cabling and connectivity	79
3.2.1 SMP Expansion connectivity	81
3.2.2 Remote Expansion Enclosure connectivity	84
3.2.3 Remote Supervisor Adapter connectivity	90
3.2.4 Serial connectivity	92
3.3 Storage considerations	93
3.3.1 xSeries storage solutions	93
3.3.2 Tape backup	98
3.4 Rack installation	99
3.5 Power considerations	101
3.6 Operating system support	101
3.6.1 Clustering	102
3.7 IBM Director support	103
3.8 Solution Assurance Review	104
3.8.1 Trigger Tool	104
3.8.2 Electronic Solution Assurance Review (eSAR)	104
Chapter 4. Installation	105
4.1 Using The Extensible Firmware Interface	106
4.1.1 EFI Firmware Boot Manager	107
4.1.2 The EFI shell	109
4.1.3 Driver Setup	117
4.1.4 Flash update	126
4.1.5 Configuration/Setup utility	132
4.1.6 Diagnostic utility	135
4.1.7 Boot Option Maintenance	136
4.2 Configuring scalable partitions	145
4.2.1 Creating a scalable partition	145
4.2.2 Booting a scalable partition	148
4.2.3 Multiple Monitors	149
4.2.4 Deleting a scalable partition	150
4.3 Installing Windows Server 2003	150
4.3.1 Important information	150
4.3.2 Preparing to install	152
4.3.3 Installation	153
4.3.4 Post-setup phase	158
4.4 Installing Linux	165
4.4.1 Linux IA-64 kernel overview	166
4.4.2 Choosing a Linux distribution	167
4.4.3 Installing SUSE LINUX Enterprise Server 8.0	170
4.4.4 Installing Red Hat Enterprise Linux AS	174
4.4.5 Linux boot process	176
4.4.6 Information about the installed system	177
4.4.7 Using the serial port for the Linux console	185
4.4.8 RXE-100 Expansion Enclosure	186
4.4.9 Upgrading drivers	187
Chapter 5. Management	189
5.1 IBM Director	190
5.1.1 Scalable Systems Manager	191
5.2 The Remote Supervisor Adapter	191
5.2.1 Connecting via a Web browser	193
5.2.2 Connecting via the ASM interconnect	198
5.2.3 Installing the device driver	199
5.2.4 Configuring the remote control password	200
5.3 Management using the Remote Supervisor Adapter	201
5.3.1 Configuring which alerts to monitor	202
5.3.2 Configuring SNMP	204
5.3.3 Sending alerts directly to IBM Director	205
5.3.4 Creating a test event action plan in IBM Director	207
5.4 Windows System Resource Manager	210
5.4.1 WSRM description	211
5.4.2 WSRM features	212
5.4.3 WSRM in the x455	213
Abbreviations and acronyms	215
Related publications	217
IBM Redbooks	217
Other publications	217
Online resources	218
How to get IBM Redbooks	222
Help from IBM	222
Index	223

Match case Limit results 1 per page

Chapter 4. Installation

107

3. Select

RAID Properties

and press Enter. If you have already configured

RAID there will be an additional screen that allows you to Modify, Sync, or

Delete the RAID array.

Figure 4-12

Configuring RAID 1

Change the Array Disk options for SCSI IDs 0 and 1 to

Yes

. These are the two

internal hard disks. Normally SCSI ID 0 is the primary disk, but this may not

be the case. All other devices will either have nothing in the Status

column, or

will say

Incompatbl

. In both cases these devices cannot be used as part of a

RAID configuration.

Once all the configuration changes are made press Esc.The following

message appears:

Warning: Data on Secondary or Hot Spare! Mirroring will overwrite!

Confirm by pressing Enter and continue.

Save the changes on the next window and exit the menu. The disks will

synchronize in the background.

LSI Logic MPT SCSI Setup Utility

Version

v1.02.11

RAID Properties

Array: IM

SCSI ID:

Size(MB):

17278

SCSI Device Identifier

Array

Hot

Status

Predict Size

Disk?

Spare

Failure (MB)

IBM-PSG ST318451LC

!#B833

[Yes]

[No]

Primary

17278

IBM-ESXSST318452LC

!#B841

[Yes]

[No]

Secondary No

17278

[---]

[---] --------- --

------

[---]

[---] --------- --

------

[---]

[---] --------- --

------

[---]

[---] --------- --

------

[---]

[---] --------- --

------

53C1030

[---]

[---] --------- --

------

IBM

25P3495a S320

[---]

[---] Incompatbl--

------

[---]

[---] --------- --

------

[---]

[---] --------- --

------

[---]

[---] --------- --

------

[---]

[---] --------- --

------

[---]

[---] --------- --

------

[---]

[---] --------- --

------

[---]

[---] --------- --

------

F1/Shift+1 =Help ArrowKeys/H,J,K,L =Select Item

-/+ =Change [Item]

Esc=Exit Menu

Home(I)/End(0) =Select Item

Enter=Execute <Item>