Home » IBM Manuals » Desktops » IBM 88554RU » Manual Viewer

IBM 88554RU Installation Guide - Page 78

Broadcom Gigabit Ethernet controller, Adapter teaming

Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

b. Disk drives c. Integrated SCSI devices d. Integrated Ethernet controller e. x455 PCI-X slots (in the order 1, 2, 3, 4, 5, 6) f. RXE-100 slots (A1, A2, A3, A4, A5, A6, B1, B2, B3, B4, B5, B6) Tip: This scan order is different from that of the x450. 3.1.4 Broadcom Gigabit Ethernet controller The x455 offers a dual Gigabit Ethernet controller integrated standard in the system. The x455 includes a single-port Broadcom BCM5704 10/100/1000 BASE-T controller on a PCI 64-bit 66 MHz bus. The BCM5704 supports full- and half-duplex performance at all speeds (10/100/1000 Mbps, auto-negotiated) and includes integrated on-chip memory for buffering data transmissions, and dual onboard RISC processors for advanced packet parsing and backwards compatibility with 10/100 devices. The Broadcom controller also includes software support for Wake on LAN, failover, layer-3 load balancing, and comprehensive diagnostics. Category 5 or better Ethernet cabling is required with RJ-45 connectors. If you plan to implement a Gigabit Ethernet connection, ensure that your network infrastructure is capable of the necessary throughput to match the server's I/O capacity. Adapter teaming The Broadcom controller is capable of participating in an adapter team for the purposes of failover, load balancing, and port trunking. The choice of adapters to team with the onboard controller depends on whether you have a copper-only network or a mixed copper/fiber network. Our recommendations are: If you have a copper Gigabit environment, use the Broadcom-based NetXtreme 1000T Ethernet adapter, part 31P6301. Alternatively, use the Intel PRO/1000 XT Server adapter, part 22P6801. If you have a mixed fiber/copper Gigabit server switch network, use the Broadcom-based 22P7801, NetXtreme 1000 SX Fiber Ethernet adapter. You can also team any of the onboard Gigabit cards with 10/100 cards such as 06P3601 and 22P4901, but this is not a recommended configuration. You can also team with the older Gigabit fiber card, 06P3701. Adapter teaming and failover work by using software additional to the adapter driver to provide the failover functionality. This software is operating system 64 IBM xSeries 455 Planning and Installation Guide Eserver

Section	Page
Front cover	1
Contents	5
Notices	9
Trademarks	10
Preface	11
The team that wrote this redbook	11
Become a published author	13
Comments welcome	14
Chapter 1. Technical description	15
1.1 Features	16
1.1.1 Comparing the x455 with the x450	16
1.1.2 Features not supported	17
1.2 The x455 base models	18
1.2.1 Front and rear views	18
1.3 System assembly	20
1.4 IBM XA-64 chipset	21
1.4.1 The processor-board assembly	23
1.4.2 The memory-board assembly	27
1.4.3 PCI-X board assembly	31
1.5 Remote Supervisor Adapter	33
1.6 RXE-100 Expansion Enclosure	35
1.7 Multinode scalable partitions	36
1.7.1 RXE-100 connectivity	38
1.7.2 Multinode configuration	39
1.7.3 Integrated I/O function support	40
1.7.4 Error recovery	40
1.8 Redundancy	41
1.9 Light path diagnostics	41
1.10 Extensible Firmware Interface	43
1.10.1 GUID Partition Table disk	45
1.10.2 EFI System Partition	47
1.10.3 EFI and the reduced-legacy concept	48
1.11 Operating system support	49
1.12 Enterprise X-Architecture	49
1.12.1 NUMA architecture	50
Chapter 2. Positioning	53
2.1 Migrating to a 64-bit platform	54
2.2 Scalable system partitioning	55
2.2.1 RXE-100 Expansion Enclosure	56
2.3 Operating system support	56
2.4 Server consolidation	57
2.5 ServerProven®	58
2.6 IBM Datacenter Solution Program	59
2.7 Application solutions	60
2.7.1 Database applications	60
2.7.2 Business logic	62
2.7.3 e-Business and security transactions	64
2.7.4 In-house developed compute-intensive applications	65
2.7.5 Science and technology industries	65
2.8 Why choose x455	66
Chapter 3. Planning	69
3.1 System hardware	70
3.1.1 Processors	70
3.1.2 Memory	71
3.1.3 PCI-X slot configuration	75
3.1.4 Broadcom Gigabit Ethernet controller	78
3.2 Cabling and connectivity	79
3.2.1 SMP Expansion connectivity	81
3.2.2 Remote Expansion Enclosure connectivity	84
3.2.3 Remote Supervisor Adapter connectivity	90
3.2.4 Serial connectivity	92
3.3 Storage considerations	93
3.3.1 xSeries storage solutions	93
3.3.2 Tape backup	98
3.4 Rack installation	99
3.5 Power considerations	101
3.6 Operating system support	101
3.6.1 Clustering	102
3.7 IBM Director support	103
3.8 Solution Assurance Review	104
3.8.1 Trigger Tool	104
3.8.2 Electronic Solution Assurance Review (eSAR)	104
Chapter 4. Installation	105
4.1 Using The Extensible Firmware Interface	106
4.1.1 EFI Firmware Boot Manager	107
4.1.2 The EFI shell	109
4.1.3 Driver Setup	117
4.1.4 Flash update	126
4.1.5 Configuration/Setup utility	132
4.1.6 Diagnostic utility	135
4.1.7 Boot Option Maintenance	136
4.2 Configuring scalable partitions	145
4.2.1 Creating a scalable partition	145
4.2.2 Booting a scalable partition	148
4.2.3 Multiple Monitors	149
4.2.4 Deleting a scalable partition	150
4.3 Installing Windows Server 2003	150
4.3.1 Important information	150
4.3.2 Preparing to install	152
4.3.3 Installation	153
4.3.4 Post-setup phase	158
4.4 Installing Linux	165
4.4.1 Linux IA-64 kernel overview	166
4.4.2 Choosing a Linux distribution	167
4.4.3 Installing SUSE LINUX Enterprise Server 8.0	170
4.4.4 Installing Red Hat Enterprise Linux AS	174
4.4.5 Linux boot process	176
4.4.6 Information about the installed system	177
4.4.7 Using the serial port for the Linux console	185
4.4.8 RXE-100 Expansion Enclosure	186
4.4.9 Upgrading drivers	187
Chapter 5. Management	189
5.1 IBM Director	190
5.1.1 Scalable Systems Manager	191
5.2 The Remote Supervisor Adapter	191
5.2.1 Connecting via a Web browser	193
5.2.2 Connecting via the ASM interconnect	198
5.2.3 Installing the device driver	199
5.2.4 Configuring the remote control password	200
5.3 Management using the Remote Supervisor Adapter	201
5.3.1 Configuring which alerts to monitor	202
5.3.2 Configuring SNMP	204
5.3.3 Sending alerts directly to IBM Director	205
5.3.4 Creating a test event action plan in IBM Director	207
5.4 Windows System Resource Manager	210
5.4.1 WSRM description	211
5.4.2 WSRM features	212
5.4.3 WSRM in the x455	213
Abbreviations and acronyms	215
Related publications	217
IBM Redbooks	217
Other publications	217
Online resources	218
How to get IBM Redbooks	222
Help from IBM	222
Index	223

Match case Limit results 1 per page

IBM

Eserver

xSeries 455 Planning and Installation Guide

Disk drives

Integrated SCSI devices

Integrated Ethernet controller

x455 PCI-X slots (in the order 1, 2, 3, 4, 5, 6)

RXE-100 slots (A1, A2, A3, A4, A5, A6, B1, B2, B3, B4, B5, B6)

3.1.4

Broadcom Gigabit Ethernet controller

The x455 offers a dual Gigabit Ethernet controller integrated standard in the

system. The x455 includes a single-port Broadcom BCM5704 10/100/1000

BASE-T controller on a PCI 64-bit 66 MHz bus.

The BCM5704 supports full- and half-duplex performance at all speeds

(10/100/1000 Mbps, auto-negotiated) and includes integrated on-chip memory

for buffering data transmissions, and dual onboard RISC processors for

advanced packet parsing and backwards compatibility with 10/100 devices. The

Broadcom controller also includes software support for Wake on LAN, failover,

layer-3 load balancing, and comprehensive diagnostics.

Category 5 or better Ethernet cabling is required with RJ-45 connectors. If you

plan to implement a Gigabit Ethernet connection, ensure that your network

infrastructure is capable of the necessary throughput to match the server’s I/O

capacity.

Adapter teaming

The Broadcom controller is capable of participating in an adapter team for the

purposes of failover, load balancing, and port trunking. The choice of adapters to

team with the onboard controller depends on whether you have a copper-only

network or a mixed copper/fiber network. Our recommendations are:

If you have a copper Gigabit environment, use the Broadcom-based

NetXtreme 1000T Ethernet adapter, part 31P6301. Alternatively, use the Intel

PRO/1000 XT Server adapter, part 22P6801.

If you have a mixed fiber/copper Gigabit server switch network, use the

Broadcom-based 22P7801, NetXtreme 1000 SX Fiber Ethernet adapter.

You can also team any of the onboard Gigabit cards with 10/100 cards such as

06P3601 and 22P4901, but this is not a recommended configuration. You can

also team with the older Gigabit fiber card, 06P3701.

Adapter teaming and failover work by using software additional to the adapter

driver to provide the failover functionality. This software is operating system

Tip:

This scan order is different from that of the x450.