Home » IBM Manuals » Desktops » IBM 88554RU » Manual Viewer

IBM 88554RU Installation Guide - Page 95

The IBM TotalStorage FAStT200 Storage Server

Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

For a complete list of supported Fibre Channel hardware, see http://www.pc.ibm.com/us/compat/machines/x455.html#Storage Note: Check the Microsoft Hardware Compatibility List (HCL) for the currently certified storage solution with FAStT for Microsoft clustered configurations and for updates to certified solutions: http://www.microsoft.com/whdc/hcl/search.mspx The IBM TotalStorage FAStT200 Storage Server The FAStT200 Storage Server is a 3U rack-mountable Fibre Channel RAID controller and disk drive enclosure. It targets the entry and midrange segment of the FC storage market. A typical use of the FAStT200 would be in a two-node cluster environment with up to 66 Fibre Channel disk drives attached to the Storage Server. Two models are available: The FAStT200 Storage Server, with a single RAID controller The FAStT200 High Availability (HA) Storage Server, which contains two RAID controllers and can therefore provide higher availability Both models feature hot-swap and redundant power supplies and fans, and you can install up to 10 slim-line or half-high FC disk drives. If you need to connect more than 10 disks, you can use the EXP500 FC storage expansion enclosures. Each EXP500 can accommodate 10 additional disk drives, and up to five EXP500s are supported on the FAStT200. This means that the maximum supported number of disk drives is 60. Hot-swappable and redundant components provide high availability for the FAStT200 Storage Server. A fan or a power supply failure will not cause downtime, and such faults can be fixed while the system remains operational. The same is true for a disk drive failure if fault-tolerant RAID levels are used. With two RAID controller units and proper cabling, a RAID controller or path failure will not cause loss of access to data. Each RAID controller has one host and one drive FC connection. The FAStT200 HA model can use the two host and drive connections to provide redundant connection to the host adapters and to EXP500 enclosures. Each RAID controller unit also contains 128 MB of battery-backup cache. The IBM TotalStorage FAStT600 Storage Server The FAStT600 Storage Server is a 3U rack-mountable Fibre Channel RAID controllers and disk drive enclosure. It targets the entry and midrange segment of Chapter 3. Planning 81

Section	Page
Front cover	1
Contents	5
Notices	9
Trademarks	10
Preface	11
The team that wrote this redbook	11
Become a published author	13
Comments welcome	14
Chapter 1. Technical description	15
1.1 Features	16
1.1.1 Comparing the x455 with the x450	16
1.1.2 Features not supported	17
1.2 The x455 base models	18
1.2.1 Front and rear views	18
1.3 System assembly	20
1.4 IBM XA-64 chipset	21
1.4.1 The processor-board assembly	23
1.4.2 The memory-board assembly	27
1.4.3 PCI-X board assembly	31
1.5 Remote Supervisor Adapter	33
1.6 RXE-100 Expansion Enclosure	35
1.7 Multinode scalable partitions	36
1.7.1 RXE-100 connectivity	38
1.7.2 Multinode configuration	39
1.7.3 Integrated I/O function support	40
1.7.4 Error recovery	40
1.8 Redundancy	41
1.9 Light path diagnostics	41
1.10 Extensible Firmware Interface	43
1.10.1 GUID Partition Table disk	45
1.10.2 EFI System Partition	47
1.10.3 EFI and the reduced-legacy concept	48
1.11 Operating system support	49
1.12 Enterprise X-Architecture	49
1.12.1 NUMA architecture	50
Chapter 2. Positioning	53
2.1 Migrating to a 64-bit platform	54
2.2 Scalable system partitioning	55
2.2.1 RXE-100 Expansion Enclosure	56
2.3 Operating system support	56
2.4 Server consolidation	57
2.5 ServerProven®	58
2.6 IBM Datacenter Solution Program	59
2.7 Application solutions	60
2.7.1 Database applications	60
2.7.2 Business logic	62
2.7.3 e-Business and security transactions	64
2.7.4 In-house developed compute-intensive applications	65
2.7.5 Science and technology industries	65
2.8 Why choose x455	66
Chapter 3. Planning	69
3.1 System hardware	70
3.1.1 Processors	70
3.1.2 Memory	71
3.1.3 PCI-X slot configuration	75
3.1.4 Broadcom Gigabit Ethernet controller	78
3.2 Cabling and connectivity	79
3.2.1 SMP Expansion connectivity	81
3.2.2 Remote Expansion Enclosure connectivity	84
3.2.3 Remote Supervisor Adapter connectivity	90
3.2.4 Serial connectivity	92
3.3 Storage considerations	93
3.3.1 xSeries storage solutions	93
3.3.2 Tape backup	98
3.4 Rack installation	99
3.5 Power considerations	101
3.6 Operating system support	101
3.6.1 Clustering	102
3.7 IBM Director support	103
3.8 Solution Assurance Review	104
3.8.1 Trigger Tool	104
3.8.2 Electronic Solution Assurance Review (eSAR)	104
Chapter 4. Installation	105
4.1 Using The Extensible Firmware Interface	106
4.1.1 EFI Firmware Boot Manager	107
4.1.2 The EFI shell	109
4.1.3 Driver Setup	117
4.1.4 Flash update	126
4.1.5 Configuration/Setup utility	132
4.1.6 Diagnostic utility	135
4.1.7 Boot Option Maintenance	136
4.2 Configuring scalable partitions	145
4.2.1 Creating a scalable partition	145
4.2.2 Booting a scalable partition	148
4.2.3 Multiple Monitors	149
4.2.4 Deleting a scalable partition	150
4.3 Installing Windows Server 2003	150
4.3.1 Important information	150
4.3.2 Preparing to install	152
4.3.3 Installation	153
4.3.4 Post-setup phase	158
4.4 Installing Linux	165
4.4.1 Linux IA-64 kernel overview	166
4.4.2 Choosing a Linux distribution	167
4.4.3 Installing SUSE LINUX Enterprise Server 8.0	170
4.4.4 Installing Red Hat Enterprise Linux AS	174
4.4.5 Linux boot process	176
4.4.6 Information about the installed system	177
4.4.7 Using the serial port for the Linux console	185
4.4.8 RXE-100 Expansion Enclosure	186
4.4.9 Upgrading drivers	187
Chapter 5. Management	189
5.1 IBM Director	190
5.1.1 Scalable Systems Manager	191
5.2 The Remote Supervisor Adapter	191
5.2.1 Connecting via a Web browser	193
5.2.2 Connecting via the ASM interconnect	198
5.2.3 Installing the device driver	199
5.2.4 Configuring the remote control password	200
5.3 Management using the Remote Supervisor Adapter	201
5.3.1 Configuring which alerts to monitor	202
5.3.2 Configuring SNMP	204
5.3.3 Sending alerts directly to IBM Director	205
5.3.4 Creating a test event action plan in IBM Director	207
5.4 Windows System Resource Manager	210
5.4.1 WSRM description	211
5.4.2 WSRM features	212
5.4.3 WSRM in the x455	213
Abbreviations and acronyms	215
Related publications	217
IBM Redbooks	217
Other publications	217
Online resources	218
How to get IBM Redbooks	222
Help from IBM	222
Index	223

Match case Limit results 1 per page

Chapter 3. Planning

For a complete list of supported Fibre Channel hardware, see

http://www.pc.ibm.com/us/compat/machines/x455.html#Storage

The IBM TotalStorage FAStT200 Storage Server

The FAStT200 Storage Server is a 3U rack-mountable Fibre Channel RAID

controller and disk drive enclosure. It targets the entry and midrange segment of

the FC storage market. A typical use of the FAStT200 would be in a two-node

cluster environment with up to 66 Fibre Channel disk drives attached to the

Storage Server.

Two models are available:

The FAStT200 Storage Server, with a single RAID controller

The FAStT200 High Availability (HA) Storage Server, which contains two

RAID controllers and can therefore provide higher availability

Both models feature hot-swap and redundant power supplies and fans, and you

can install up to 10 slim-line or half-high FC disk drives. If you need to connect

more than 10 disks, you can use the EXP500 FC storage expansion enclosures.

Each EXP500 can accommodate 10 additional disk drives, and up to five

EXP500s are supported on the FAStT200. This means that the maximum

supported number of disk drives is 60.

Hot-swappable and redundant components provide high availability for the

FAStT200 Storage Server. A fan or a power supply failure will not cause

downtime, and such faults can be fixed while the system remains operational.

The same is true for a disk drive failure if fault-tolerant RAID levels are used. With

two RAID controller units and proper cabling, a RAID controller or path failure will

not cause loss of access to data.

Each RAID controller has one host and one drive FC connection. The FAStT200

HA model can use the two host and drive connections to provide redundant

connection to the host adapters and to EXP500 enclosures. Each RAID

controller unit also contains 128 MB of battery-backup cache.

The IBM TotalStorage FAStT600 Storage Server

The FAStT600 Storage Server is a 3U rack-mountable Fibre Channel RAID

controllers and disk drive enclosure. It targets the entry and midrange segment of

Note:

Check the Microsoft Hardware Compatibility List (HCL) for the currently

certified storage solution with FAStT for Microsoft clustered configurations and

for updates to certified solutions:

http://www.microsoft.com/whdc/hcl/search.mspx